I have a Dell Truemobile 2300 wireless router. We have 2 xbox's in our house and we want an Open NAT setting on each (Current NAT setting is moderate) Can this be done? If so, how?

some routers dont have wps button but if you need to reset router To restart the Dell TrueMobile 2300 Wireless Broadband Router, unplug the power connector and plug it back in.

To load the Dell TrueMobile 2300 Wireless Broadband Router's default settings, hold down the reset button on the router for at least five seconds. While the unit resets, the Power light blinks.

with verizon, you need to set the modem to full bridged mode so that the connection from your modem will be opened. This certain firewall is called NAT. Your modem and your router has this feature. To disable NAT on your modem, you need to set it to full bridged mode. To disable the NAT on your router, you need to open ports on your router.

You need to open this port on the router for Xbox live to work
TCP: 80, 3074, 53

UDP: 88, 3074

forward it to the ip of your Xbox.

this should set the NAT on your xbox to open, not moderate.

You Will Have to Disable the Firewall In Your modem / Router

And IF it is a router then Open The Ports

• TCP 80
• UDP 88
• UDP 3074
• TCP 3074
• UDP 53
• TCP 53


And also make sure that UPnP is enabled

How to secure the wireless network

You want to secure the wireless network.
Is there any computer connected to the router with the Ethernet cable?
If not then you will need to connect the computer to the router with the cable.
Check the IP address on the computer. Open the router set up page.
Once you open the set up page, you will find the option to make it secured

you need to set your nat type to open.

here are some step by step instructions that will help you do that.

http://www.xbox360forum.com/xbox-forum/threads/51908-How-To-Open-NAT.-xbox-360.

Dell™TrueMobile™2300 Wireless Broadband Router
User's Guide

http://support.dell.com/support/edocs/network/p57205/en/index.htm

Configuring Your Dell™ TrueMobile™ 2300 Router for Gaming

Follow below steps to set up the router for gaming:

1. Select the system or systems to be used as game systems.
   
2. Locate the MAC address. For Windows 2000 and XP
   
   1. Click Start -> Run.
   2. Type cmd, and click OK.
   3. On the command prompt, type ipconfig /all
   4. Write down the MAC (Physical) address of your computer to configure for gaming.
      
3. Open the web browser, and type http://my.router (or http://192.168.2.1)
   
4. Click the Advanced Settings tab.
   
5. Click the DHCP Server Settings tab on the left navigation bar.
   
6. Click Add button in IP Address Reservation,
   1. Enter the MAC address of the system you wish to use for gaming in MAC Address field.
   2. Enter an IP address for the system (select a number between 101 and 254)
      
7. Click Submit.
   
8. Click the Port Forwarding Settings tab on the left navigation bar.
   1. To set a single computer for gaming, check the Enable DMZ Host box.
   2. Enter the IP address of the system at DMZ IP Address field.
   3. Click Submit.
      NOTE: Only a single computer can be set for DMZ service. To set multiple computers for gaming, please post your query again
      
9. Reboot the client system. The client system will use the newly assigned IP and will not have any TCP/IP ports blocked by the firewall feature of the router.

Look for a setting like "Virtual DMZ Host". It's hard to tell for sure without knowing the make and model of your router.

Before you throw it, save all the settings in router and try a re-start or there is normally a re-set button somewhere to press and set it back to factory settings. If the wireless re starts re-load previous settings. Please rate solution.

If you are able can you reset the router in any way normally little reset button on back, or get into the routers set up page and try a restart.