The f1 code on the Maytag Bravos top loading washer keeps going off and stopping the machine

Maytag Bravos MTW6600T Top Load Washer Run ... - Fixya

www.fixya.com > ... > Maytag Bravos MTW6600T Top Load Washer

Maytag Bravos MTW6600T Top Load Washer, run diagnostic test cycle related issues. Get free help, solutions & advice from top Maytag experts.

Maytag Bravos MTW6600T Top Load Washer Run ... - Fixya

www.fixya.com > ... > Maytag Bravos MTW6600T Top Load Washer

Maytag Bravos MTW6600T Top Load Washer, run diagnostic test ccu related issues. Get free help, solutions & advice from top Maytag experts.

Maytag Bravos MTW6600T Top Load Washer Diagnostic ...

Call Whirlpool at 800-688-9900.

I think there is a recall on that machine.



Let them know you have a Bravos or Oasis washer and you are getting a F1 error code.

I think they will send someone out to replace the controller board for free on that unit. If not, here is the part you need.

Call Whirlpool at 800-688-9900.

Let them know you have a Bravos or Oasis washer and you are getting a F1 error code.

They will send someone out to replace the controller board for free!
If not, here is a link to the control board you need.

F1 is a very bad error unfortunately. Try unplugging the unit 60 seconds to see if it will reset the control board. If not, then you will need a new relay control board which is about $200, because F1 means that the board has detected an internal short inside the control board itself.

Here is a manual that might have the answer for you:
http://steprightupmanuals.com/washing-machine-service-manuals/maytag-washing-machine-service-manuals/maytag-models-mtw6500-mtw6600-bravos-washer-service-repair-man
prem

This problem has been found to be inherent with this model including its Whirlpool (Cabrio) and Maytag (Bravos) counterparts. It is due to the design of the water level control system, the pressure transducer, which has been integrated with the machine/motor control assembly. It has been found that issues with the pressure transducer including the pressure hose results in the flashing of the fault code F1. Air leaks and moisture in the pressure hose and lint or flashing in the air dome can result in signal error being sent to the machine/motor control assembly and hence the fault code F1 which is according to the service manual, a machine/motor control fault. You may observe that this fault code appears whenever water runs into the machine.

Whirlpool, the manufacturer of these models, has issued a bulletin regarding this issue and suggested the necessary actions in identifying the real cause of this problem and how to address it. Click on the link below for the troubleshooting and repair details.

Troubleshooting Fault Code F1 on Whirlpool Cabrio, Kenmore Elite Oasis, and Maytag Bravos Top Load Washers

Defective hall sensor most likely, The cabrio bravos and Oasis machines are all basically the same.
MORE here

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

you can go to appliancerepairplanet.vstore.ca and we can get you a sevice manual on it go to contact us

You must have trash or sediment in your pressure tube hose. Remove it from the pressure switch and blow the stuff out then re-secure the hose and pump out any water in the tub. Then retry. Use this handy dandy service manual as a GUIDE


If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61