Riso in Jam and on the creen say: Check setting and red light on number 4. When I press * key it say -227 and P-08. I don't know what to do please help. Thanks

hi,
To make your BD player you need One for all universal remote control

Full procedure for a oneforall remote is as follows:

1. Press DVD
2. Hold the magic button until the DVD button flashes twice.
3. Press 0533

4. Hold the magic button until it flashes twice.
5. Press 994
6. Press Magic Key (don't hold)
7. Press 00189 (if your oneforall remote uses 4 digit or 3 digit codes, use less leading zeros)
8. Press 1 ( this sets it to key 1 - it flashes twice )

9. Hold the magic button until it flashes twice.
10. Press 994
11. Press Magic Key (don't hold)
12. Press 00255
13. Press 2 ( this sets it to key 2 - it flashes twice )

14. Hold the magic button until it flashes twice.
15. Press 994
16. Press Magic Key (don't hold)
17. Press 00095
18. Press 3 ( this sets it to key 3 - it flashes twice )

19. Hold the magic button until it flashes twice.
20. Press 994
21. Press Magic Key (don't hold)
22. Press 00221
23. Press 4 ( this sets it to key 4 - it flashes twice )

24. Hold the magic button until it flashes twice.
25. Press 994
26. Press Magic Key (don't hold)
27. Press 00079
28. Press 5 ( this sets it to key 5 - it flashes twice )

The remote is now programmed and ready to use, to make the BDV-E370 region free:

1. Use the remote that came with the player to bring the player out of standby, make sure there isn't a disc in it.
2. Press 1, 2, 3, 4, 5 on the oneforall remote. The 24p light will start flashing. (Centre light)
3. Put the player back into standby with the Sony remote.
4. Hard reboot machine (remove power)to prevent the 24p light flashing indefinitely.
5. Next time you turn on the player it will be region free for DVD playback.
ok

The machine does not work due to a paper jam or some sensor problem.
Clear the paper jam. If the problem still continues after clearing the paper jam, try to clean the encoder strip behind the printer head.

Also, try a reset:


The proper reset code sequence to reset DCP printers without numeric keypad should be as follows:

1. press buttons Set, Menu, Mono Start one by one, followed by up arrow key four times. this should all be done as short a time as possible, around 3 seconds.

2. enter maintenance mode 80 by pressing the up/down arrow key and set key to select numbers 8 and 0

3. press up arrow key several times to get to the Purge item

4. enter 2, 7, 8 and 3 using arrow/set keys to reset the counter

5. press Stop/Exit key to go to root of maintenance mode

6. enter 9,9 to exit maintenance mode

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Hi,

Configuring codes:
Turn on the component that you want to set up.

1.Hold the component key down until the green indicator light comes on. The green light should come on after approximately 3 seconds.

2.Release the component key.

3.If you are programming the DVD or CD device press the "action" key. The red indicator light will come on.

4.Within thirty seconds, enter in a 4-digit code number. The component key lights will blink with an upward motion when a code has been successfully entered. In this case proceed to step #5. If the code has not been successfully entered, the componment lights will not blink. In this case return to strep #1 and start over.

5.Test code by pressing "Power" key. If the component turns off, you've got the right code. Follow the same instructions to set up your other components. If the component doesn't turn off, return to step 2 and use the next 4-digit code listed.


Auto Code Scan:
The Auto Code Scan feature allows you to set up your components without having to enter in code numbers. The Jensen will do the work for you!

1.Turn on the component that you want to set up.

2.Hold the component key down until the light comes on. The green light should come on after approximately 3 seconds.

3.Release the component key.

4.If you are programming the DVD or CD device press the "action" key. The red indicator light will come on.

5.Press "0" - "9" The green light will blink as codes are sent.

6.As soon as the remote turns your component off, press the "action" key. The component key lights will blink with an upward motion when a code has been successfully entered. The component is now programmed.

7.If none of the codes turn your component off, return to step 2 and start over.

Thanx

riso rp 3790 no imprime, no copia, me dijeron que borrara errores pero no se donde, creen que sea eso

please follow the instruction and you will reset the copier:
press the follow keys in order:
1. press the yellow key[c] (clear)
2. press 1-0-7 on the number pad
3.press and hold it pressed the red key [c] (stop)
4.When on the screen will appear other menu different from the usual turn off the machine from the main switch (the red switch) and then turn it on after 5 seconds.
Please answer do this is helpful for we to know if is needed some more information.(if this was not helpful you will need to write the machine model number)

We will see black bars on the video sometimes. In fact, it is all about aspect ratios. In the old days, the 4:3 aspect ratio is a standard format, but with the development of technology, 16:9 format appears. So when you play 4:3 format video in a 16:9 play window, naturally, black bars will appear. This time, you can also crop a video to fit the aspect ratio too. Keep reading to know how to crop a video.

your error code should be 6 digits.
Always press the reset button its the yellow button with 2 parallel lines

refix your ink cartrdige also check there is not any paepr jam issue.
also some times printer neeed servicing creates this type of issue.

from fixya knowledge base I found this solution

1. Power Unit off

2. Open front cover

3. Press and hold GO and turn power on

4. When all 3 lights lit release and press GO twice

5. All lights turn solid

6. With all solid, press GO 5 times

7. Ready light GOes red

8. Close door and you're all set
Let know if working and don't forget to rate solution