Message NO ID message followed by beep beep beep

You can set or change the answering system options from any handset.
Open the menu and select Ans setup then select Message alert and activate it!

Beeps will be on!

If you have Polycom Sound Station 2 and you are getting NO ID Message on screen. Please do the following:

1. Press Speaker
2. 773

This should clear up the error.

You've got unheard messages on the voicemail system provided by your telephone company. This system records messages when someone calls while you're already on the phone. Please contact your telephone company for instructions on accessing their voicemail system.

You have unheard messages on the voicemail system provided by your telephone company. This system takes messages when someone calls while you're already on the phone. Please contact your telephone company for instructions on accessing their voicemail system.

ACTUALLY MAY POLYCOM SOUND STSTION ARE NOT DAMMAGE WHEN I BUY IT.WHEN THE TYPOON IS COMING SINCE ONDOY.MY POLYCOM SOUND STSTION ARE WET COZ OF TYPOON. JUST TELL ME WHERE IS THE SERVICE CENTER OF POLYCOM

Hi,

To retrive the messages remotely please follow the steps...

Dialing In to Your System:-

1.Call your telephone number and wait for the system to answer. (If your answering system is off, it will answer after ten rings and sound a series of beeps instead of your greeting.)

2.During the greeting or beeps, press 0 and immediately enter your security code. If you enter it incorrectly 3 times, the system hangs up and returns to standby.

3.The system announces the current time, the number of messages stored in memory, and a help prompt. It will beep intermittently to let you know it's waiting for your command.

When you hear beeping, enter a 2-digit command from below:-

01Repeat message
02Play message
03Skip message
04Delete message
05Stop playback
06Turn the system on
09Turn the system off
10Hear help prompts

Thanx

The caller id information is sent from your local telco provider after the first ring and might not be able to be extended to the individual sets, try backing off the ring to answer on your voice mail from 2 to 3 rings to see if the information is then passed on. The Voice Messaging System message is being sent from the system showing who transfered the call to you. You should also notice that the ring pattern when that message is displayed is a standard ring followed by a beep meaning a transfer is taking place.

My ps3 didnt read my ps3 games..followed these instructions and it worked!!

http://boardsus.playstation.com/playstation/board/message?board.id=ps3updates&thread.id=52730

1. Plug in controller

2. Have system in standby mode (red light)

3. Hold down power button for a full cycle (will turn on and back off again)

4. Hold power button again will hear 2 single beeps then a double beep.

5. As soon as you hear the double beep immediately remove your finger from the power button.

6. Hit the PS button on controller when it tells you to

7. Go to ONLY option 3 (restore)

8. WARNING: select any other option and you can wipe out everything ONLY USE OPTION 3

9. Follow on screen prompts

Thanks to Krazyfox

The default security code is "80". If you have not reset that code, you will use 80.
This is all from the manual:
1) Call your telephone number and wait for the system to answer. If the answering system is off, it will answer after about ten rings and sounds a series of beeps.
2) During the greeting or the beeps (if answering system is off), press 0 (zero) and enter your security code within 2 seconds.
3) The answering system announces the current time and the number of messages stored in memory. You hear "To play incoming messages, press zero-two. For help, press one-zero" followed by a beep.
Then the manual lists all the remote commands. If you need those, you can go to uniden.com and download a manual.

Here is a link to the site containing a pdf manual link and this is an excerpt for you :

Long Distance calls and Area Code Setting/Cancellation
While the present Caller ID information is displayed, pressing */tone/< will place
or remove the prefix "1" in the display to set the call for a long distance call, or
pressing #/> will set or cancel an area code (see page 30).
Storing Caller ID messages in the Phonebook
Messages shown in the Caller ID list can be stored in the phonebook. The phone
number and name of the party on the Caller ID list can be stored in memory.
1) When the phone is in standby mode, select the Caller ID message to be stored.
Then press the STORE soft key on the base or the EDIT soft key on the handset.
From the handset, then select E D I T ?. S t o r e / E d i t N a m e appears. If the Caller ID
message is already stored in memory, you will hear a beep and T h i s d a t a i s
a l r e a d y s t o r e d ! ! appears. The number will not be stored.
2) To complete the setting, follow the steps 3-8 in "Phonebook (Storing Phone
Numbers, Names, Distinctive Rings, and Speed Dial)" on pages 42-43.