I have a GE wcx1070 and it will not agitate or spin will fill the tub and drain but won't spin. I have checked for obstrutions in the tub and under the agitater. and the belt looks good if it does spin it spins real slow and will stop, It won't even make a full rotation. Does anybody have an Idea of what this could be?

Question 1

0helpful

1answer

GE WPGT9150HWW Washing machine Problem

check belt under unit if ok check under agitator for bad cog splines

Oct 01, 2022 • GE Washing Machines

0helpful

2answers

I have a GE washer model# 175D2750G041 after the washer fills up with water and starts to spin to wash it makes a awful noise but only when spinning to wash not spin to drain water . what could it be

Your question is confusing. A washer doesn’t spin when it washes. It agitates. A washer fill with water, agitate, drain then spin water out. Please reword your question.

Jul 03, 2022 • GE Washing Machines

0helpful

1answer

My GE washer G153 was making a loud noise when draining/spinning out. Next load filled up with water and done nothing else. Now machine turns on but will do nothing.

have an electrician check out the agitator control module. This unit controls the agitation action of the machine and gets power when the tub fills to the desired level and switches over.

Aug 17, 2013 • GE Washing Machines

0helpful

1answer

Ge washer 175d2750g116

Check for a loose grub screw in the pulley that is not transferring the shaft motion to the pulley. It will ne a hex hole and will require an allen key to tighten it uo

Aug 17, 2013 • Washing Machines

33helpful

1answer

WASHER FILLS WITH WATER, THEN WON'T AGITATE. TURN KNOB TO SPIN AND IT DRAINS THEN SPINS. STILL WON'T AGITATE

WASHER FILLS WITH WATER, THEN WON'T AGITATE. TURN KNOB TO SPIN AND IT DRAINS THEN SPINS. STILL WON'T AGITATE please show me a diagram

Jun 14, 2011 • Whirlpool LSR7333 Top Load Washer

0helpful

2answers

Water runs but doesn't fill tub and wont spin if put on spin cycl

The water-level switch regulates your washer's fill volume. This switch is usually a diaphragm device with a small, clear tube attached between the switch and the bottom of the washer's outer tub. As the water level in the tub increases, the pressure on the air in the tube increases. When the pressure reaches a certain level, it activates the switch, shuts off the water, and signals the timer to begin the agitate cycle. If the switch is defective, it may prematurely signal the water to shut off. If so, you probably need to replace the water-level switch.

Jan 09, 2010 • GE WBSE2090A Top Load Washer

8helpful

2answers

Washer will not agitate but fills/drains/spins

Could be related to pressure switch which measures the amount of water in tub. Does it fill and then just sit there?

Nov 13, 2009 • GE 3.2 Cu. Ft. 6-Cycle Super Capacity...

0helpful

1answer

Agitator problem

Check to see if any thing is under the agitator. If not then maybe the bearings going out or other part of machine . Besure the cap is tighten so agatator don't come off. Check for ware on agatator top to the tighting nut.

Jun 02, 2009 • GE WPGT9360E Profile Harmony 4.0 cu. ft....

0helpful

1answer

Will not go in to spin cycle

Remove agitator (it will pop off when pried) then you will find your answer. Mine was a broken tub collar to shaft.

May 09, 2009 • GE WBSR3140DW Top Load Washer

15helpful

3answers

Kenmore 70 series

Okay...I'm a little confused on your symptoms. You initially said it fills, but doesn't agitate or spin, but drains.

Then, you finished with the washer filling, no agitate or spin, but now doesn't drain.

Which one is it?

The symptoms you describe are usually associated with the following:

1. Fills, may or may not agitate, won't spin or drain - lid switch.
2. Fills, may or may not agitate, won't spin, but still drains - motor coupling.
3. Fills, may or may not agitate, won't spin or spins slow - gear case.
4. Fills, agitates, spins, but does not drain – water pump.

NOTE: These are the more common failure items with these symptoms.

Double check the lid switch by opening and closing the lid. You should hear a clicking noise to indicate the switch is working. The switch is located under the top panel along the wash tub rim on the right-hand side. If not, check to make sure the lid strike (small plastic piece on the lid itself) is in place. This activates the lid switch when the lid is closed. Also, check the mounting screws along the rim (there are two of them) to see if they are tight.

If the motor coupling were bad, the washer would still drain, but there would be a rattling sound as the washer tries to spin or agitate.

If you need replacement parts, go to searspartsdirect.com and type in your model number in the "Search by Model Number" window. The lid switch can be found under the "Top and Cabinet" heading as item number 11 (part #3949238). Instructions on how to replace are located at the following link:

http://www.fixya.com/support/r385199-replacing_lid_switch_whirlpool_top

If you wish to replace the motor coupling, the part can be found under the “Brake/Clutch/Gearcase/Motor/Pump” heading as item number 13 (part #285753A). If you need instructions on how to replace, just follow this link:

http://www.fixya.com/support/r385250-replacing_motor_coupling_kenmore_top

Now, there’s a couple of ways to drain the washer. If it’s a simple lid switch problem, you don’t need to drain the washer to replace the switch. With a broken switch repaired, the washer will run and drain by itself. However, if you wish to drain the tub you can use a shop vac to pull a vacuum on the drain hose. This may take a few times depending on the size of the shop vac. These wash tubs typically have about a 35 gallon capacity. If you do not own a shop vac, you can by-pass the lid switch by jumpering the two BLACK wires at the lid switch connector that is connected to the console. CAUTION: Make sure you UNPLUG the washer before jumpering, then plug back in.

I hope this information is helpful to you. If I’m wrong about the symptoms, please post back and update me on what the washer is or is not doing, so I can assist you further.

May 15, 2008 • Kenmore 24032\24036 Top Load Washer

Question 2

Dan Webster

GE Master 8,221 Answers
Posted on Aug 06, 2010

Dan Webster

GE Master

Joined: Dec 14, 2008

Answers

8221

Questions

5

Helped

2380782

Points

25840

I think it might be the lid switch. I have a GE wcx1070 - 8e3407e.jpg as you can see it can fail mechanically and electrically. To get to the lid switch you remove the front panel firstthen you can remove the top and access the slid switch.
Use this training manual

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Answer 2

wayne stanlield

Contributor 1 Answer
Posted on Jan 19, 2014

wayne stanlield

Contributor

Joined: Jan 19, 2014

Answers

1

Questions

1

Helped

122

Points

1

Grinds in spin cycle at bottom of wash tub on spin cycle

Related Topics:

Trustworthy Expert Solutions

2 Answers

Dan Webster

wayne stanlield

Add Your Answer

Attachments: Added items

Related Questions:

GE WPGT9150HWW Washing machine Problem

I have a GE washer model# 175D2750G041 after the washer fills up with water and starts to spin to wash it makes a awful noise but only when spinning to wash not spin to drain water . what could it be

My GE washer G153 was making a loud noise when draining/spinning out. Next load filled up with water and done nothing else. Now machine turns on but will do nothing.

Ge washer 175d2750g116

WASHER FILLS WITH WATER, THEN WON'T AGITATE. TURN KNOB TO SPIN AND IT DRAINS THEN SPINS. STILL WON'T AGITATE

Water runs but doesn't fill tub and wont spin if put on spin cycl

Washer will not agitate but fills/drains/spins

Agitator problem

Will not go in to spin cycle

Kenmore 70 series

Not finding what you are looking for?

WVSR1060A Top Load Washer

GE WPGT9150HWW Washing machine Problem

Ask a Question

Top GE Washing Machines Experts

Brad Brown

Virgil Watts

Steve Sweetleaf

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Manuals & User Guides

. WVSR1060A Top Load Washer Manual

. WVSR1060A Top Load Washer Manual

Related Topics:

Trustworthy Expert Solutions

2 Answers

Dan Webster

wayne stanlield

Add Your Answer

Attachments: Added items

Related Questions:

GE WPGT9150HWW Washing machine Problem

I have a GE washer model# 175D2750G041 after the washer fills up with water and starts to spin to wash it makes a awful noise but only when spinning to wash not spin to drain water . what could it be

My GE washer G153 was making a loud noise when draining/spinning out. Next load filled up with water and done nothing else. Now machine turns on but will do nothing.

Ge washer 175d2750g116

WASHER FILLS WITH WATER, THEN WON'T AGITATE. TURN KNOB TO SPIN AND IT DRAINS THEN SPINS. STILL WON'T AGITATE

Water runs but doesn't fill tub and wont spin if put on spin cycl

Washer will not agitate but fills/drains/spins

Agitator problem

Will not go in to spin cycle

Kenmore 70 series

Not finding what you are looking for?

WVSR1060A Top Load Washer

GE WPGT9150HWW Washing machine Problem

Related Topics

Ask a Question

Popular Questions

GE front load washer (clothes)

My Ge washing machine is leaking from the Bottom

GE top load Washer ripping clothes

"Dr" error code

GE Adora Front Load Washing Machine Problem

Top GE Washing Machines Experts

Brad Brown

Virgil Watts

Steve Sweetleaf

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Manuals & User Guides

. WVSR1060A Top Load Washer Manual

. WVSR1060A Top Load Washer Manual