I pulled out the usb connection from my computer on accident and I cannot get it to work anymore...i tried the reset button...tried usb connection, tried everything except opening it up...it just doesnt respond at all.

No,there is not, you might go to settings and check, If the USB receiver is bad neither keyboard or mouse will work. It would be better to replace with a better brand. reviews are not favorable.

A quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. Simply disconnect the printer from your computer (if USB connected)> reboot your pc > unplug and re-plug the printer into the power source to reset it. When the printer turns on, reconnect it to your computer (if USB connected). Then try to print again once the computer fully recognizes the USB connection or when the WiFi light on the printer turns solid green (if WiFi connected.).

If that doesn't help, try the steps below:

1. Disconnect the USB cable connecting the printer from your computer.
2. On your computer, go to Control Panel > Printers and Faxes.
3. Delete the Lexmark print object.
4. Reboot computer.
5. Re-brick your printer by pulling out the power supply - black box where the power cord is plugged into on the back of the printer, and re-plug after 30 seconds.
6. When the printer turns on, reconnect it to the computer.
7. Wait until your computer fully recognizes the USB connection. To check, go to Control Panel > Printers and Faxes. If you see a new Lexmark print object in the list, try to print a document to verify that the problem is fixed.

I have this problem all the time.. if you already changed the battery what you need to do is remove the usb that came with it from the computer cause most likely when you changed the batteries it reset the code for your computer and mouse so, take the usb out that came with the mouse and hit the button on the mouse ... take the usb out and replug it and it should work soon as you hit the button on the mouse...


hope this helps...

Same problem. But I am able to set the location, time and date while usb connected. As soon as I pull it out, total failure. Even tried the RESET button on back, but nothing works.
Anybody... anybody?

Normal 0 Turn the mouse over and find the small rest/connect button on the bottom of the mouse and press it to Reset/Connect the mouse to the receiver and work properly.
If not, try pressing the receiver button and then press the mouse. This should be done whenever you change batteries or glitch.
Hope this helps you. Bud

I try this to my customer canon printer and it is working even i used only the step one method.

Here's the steps for reseting "Waste Ink Full" problem at iP1000

Step 1: Manual for Service mode (1st method)
1. Unplug POWER and USB cables.
2. Open door of the printer, PRESS and HOLD the POWER button.
3. Connect the POWER cable.
4. Close door, then release POWER button.
5. Power ON your printer a usual (It should not blinking anymore)

Step 1: Manual for Service mode (2nd method)
1. Unplug POWER and USB cables.
2. PRESS and HOLD the POWER button,
3. Connect the POWER cable.
3. Release the the POWER button
4. Power ON your printer a usual (It should not blinking anymore)


Step 2 : Software for Permanant (1st method)
1. Reconnect the USB cable and turn ON your Printer
2. Open "General Tools for iP1000",
http://www.printersiam.com/data/download/iP1000%20Service%20Tool.zip
3. Select (USB PORT)
4. Choose (SET DESTINATION 1)
It should be reseted already, but somehow it start blinking again if you ever unpluging AC POWER cable. So try the 2nd method by using ServiceTool for IP1500

Step 2 : Software for Permanant (2nd method)
1. Reconnect the USB cable and turn ON your Printer
2. Open "General Tools for iP1500",
http://www.printersiam.com/data/download/iP1500%20Service%20Tool.zip
3. Select (USB PORT)
4. Choose CLEAR WASTE INK COUNTER - MAIN
5. Choose CLEAR WASTE INK COUNTER - PLATEN
It should be working, coz my printer now now work normally

Could be a hardware problem. Sometimes ipods will not connect to a computer even when everything else is working fine.

You have to use the USB cable and do it through your computer. There is no way to change the time on the watch. Bad design.

I'd suggest bringing it back to the store where you purchased it or phoning a samsung help line.

First deconnect all batteries, usb cable anything from the camera. Leave it for about 1 hour and then without connecting batteries press and keep the the power button pressed for about 1min. Then press twice on every other button including the shuter, zoom or stuff like that. This should reset a microcontroller that remembers the last operation done. This doesn't reset the camera. After this, connect the batteries and try to power it again. IF this doesn't work. Try to push the lens back in using your fingers. Don't force them to much if they doesn't appear to go back. Use 2 fingers to press on the lens one on each side aplying equal pressure. You may hear a click noise when the lents start to go back. Again, don't force them to much. Try these at first and then if they doesn't work, please post back and specify what does the camera do. No led's no nothing or ..?