I-mate SP3i how do I send data with bluetooth

To set up Bluetooth on your phone

1. Go to Menu, select Connect or Connections or Connectivity:

Note! If the above steps do not work, please consult the user manual.

2. Bluetooth - Select On to enable Bluetooth.

3. My telephone's visibility - Select Shown to all if you want your device to be found by other Bluetooth devices. If you select Hidden, your device cannot be found by other devices.

4. My Bluetooth name - Define a name for your device. After you have activated your Bluetooth service and changed My phone's visibility to Shown to all, your phone and this name can be seen by other Bluetooth device users.

Sending data via Bluetooth

If your phone supports the Bluetooth 1.1 specification or earlier, you can only have one Bluetooth connection running on your phone at any one time.

1. Select or open the file you wish to send. For example, to send a photo to another device, open the Gallery application.

2. Select the file you wish to send, then select Options > Send > via Bluetooth.

3. The phone starts to search for devices within range.

Devices using Bluetooth technology that are within range will appear on the display. You should see a device icon, the device's name, the device type, or a short name. (A paired device is one where a Bluetooth connection already exists between your phone and the other device.)

• To interrupt the search, press Stop. The device list freezes and you can start to form a connection to one of the devices already found.

If you have searched for devices earlier, a list of the devices that were found previously is shown first. To start a new search, select More devices. If you switch off the phone, the list of devices is cleared and the device search needs to be started again before sending data.

4. Scroll to the device you want to connect with and press Select. The item you are sending is copied to Outbox and the note Connecting is shown.

5. Pairing (if this is not required by the other device, proceed to step 6.)

• If the other device requires pairing before data can be transmitted, a tone sounds and you are asked to enter a passcode. • Create your own passcode (1-16 characters long, numeric) and agree with the owner of the other device to use the same code. This passcode is used only once and you do not have to memorise it. • After pairing, the device is saved to the Paired devices view.

6. When the connection has been successfully established, the note Sending data is shown. Data received via Bluetooth can be found in the Inbox folder in Messaging. Tip: Pairing is a means of authentication. The users of the devices using Bluetooth technology should agree together what the passcode is, and use the same passcode for both devices in order to pair them. Devices that do not have a user interface have a preset passcode.

Checking the status of the Bluetooth connection

• When the Bluetooth icon is shown in standby mode, Bluetooth is active.

• When the Bluetooth icon is blinking, your phone is trying to connect to the other device. • When the Bluetooth icon is shown continuously, the Bluetooth connection is active.

Receiving data via Bluetooth

When you receive data via Bluetooth, a message alert tone is played and you are asked if you want to accept the message. If you accept, the item is placed in the Inbox folder in Messaging.

Disconnecting Bluetooth

A Bluetooth connection is disconnected automatically after sending or receiving data.

Hi, to set up Bluetooth on your phone

1. Go to Menu, select Connect or Connections or Connectivity:

Note! If the above steps do not work, please consult the user manual.

2. Bluetooth - Select On to enable Bluetooth.

3. My telephone's visibility - Select Shown to all if you want your device to be found by other Bluetooth devices. If you select Hidden, your device cannot be found by other devices.

4. My Bluetooth name - Define a name for your device. After you have activated your Bluetooth service and changed My phone's visibility to Shown to all, your phone and this name can be seen by other Bluetooth device users.

Sending data via Bluetooth

If your phone supports the Bluetooth 1.1 specification or earlier, you can only have one Bluetooth connection running on your phone at any one time.

1. Select or open the file you wish to send. For example, to send a photo to another device, open the Gallery application.

2. Select the file you wish to send, then select Options > Send > via Bluetooth.

3. The phone starts to search for devices within range.

Devices using Bluetooth technology that are within range will appear on the display. You should see a device icon, the device's name, the device type, or a short name. (A paired device is one where a Bluetooth connection already exists between your phone and the other device.)

• To interrupt the search, press Stop. The device list freezes and you can start to form a connection to one of the devices already found.

If you have searched for devices earlier, a list of the devices that were found previously is shown first. To start a new search, select More devices. If you switch off the phone, the list of devices is cleared and the device search needs to be started again before sending data.

4. Scroll to the device you want to connect with and press Select. The item you are sending is copied to Outbox and the note Connecting is shown.

5. Pairing (if this is not required by the other device, proceed to step 6.)

• If the other device requires pairing before data can be transmitted, a tone sounds and you are asked to enter a passcode. • Create your own passcode (1-16 characters long, numeric) and agree with the owner of the other device to use the same code. This passcode is used only once and you do not have to memorise it. • After pairing, the device is saved to the Paired devices view.

6. When the connection has been successfully established, the note Sending data is shown. Data received via Bluetooth can be found in the Inbox folder in Messaging. Tip: Pairing is a means of authentication. The users of the devices using Bluetooth technology should agree together what the passcode is, and use the same passcode for both devices in order to pair them. Devices that do not have a user interface have a preset passcode.

Checking the status of the Bluetooth connection

• When the Bluetooth icon is shown in standby mode, Bluetooth is active.

• When the Bluetooth icon is blinking, your phone is trying to connect to the other device. • When the Bluetooth icon is shown continuously, the Bluetooth connection is active.

Receiving data via Bluetooth

When you receive data via Bluetooth, a message alert tone is played and you are asked if you want to accept the message. If you accept, the item is placed in the Inbox folder in Messaging.

Disconnecting Bluetooth

A Bluetooth connection is disconnected automatically after sending or receiving data.

The phone will search for a couple seconds. If your headset is in paring mode, it will show up on the phone either with the name of device or something like this [unknown headset] or [b2.c3.f4.56.a1] (called a MAC address).

Either way, select it, and hit OK.


The phone will now ask you for a "Pin" or "Passcode", which is a 4 digit number. Headsets will ALWAYS have 0000 (four zeros) as a pin or passcode. I have never encountered a headset with a different number as a passcode. I have been in wireless for 10 years, and still have not found a headset that has any different numbers.

Enter these four zeros and select "OK"

Hope that helped...


Thanks for using fixya...

Hi, To set up Bluetooth on your phone

1. Go to Menu, select Connect or Connections or Connectivity:

Note! If the above steps do not work, please consult the user manual.

2. Bluetooth - Select On to enable Bluetooth.

3. My telephone's visibility - Select Shown to all if you want your device to be found by other Bluetooth devices. If you

select Hidden, your device cannot be found by other devices.

4. My Bluetooth name - Define a name for your device. After you have activated your Bluetooth service and changed

My phone's visibility to Shown to all, your phone and this name can be seen by other Bluetooth device users.

Sending data via Bluetooth

If your phone supports the Bluetooth 1.1 specification or earlier, you can only have one Bluetooth connection running

on your phone at any one time.

1. Select or open the file you wish to send. For example, to send a photo to another device, open the Gallery

application.

2. Select the file you wish to send, then select Options > Send > via Bluetooth.

3. The phone starts to search for devices within range.

Devices using Bluetooth technology that are within range will appear on the display. You should see a device icon,

the device's name, the device type, or a short name. (A paired device is one where a Bluetooth connection already

exists between your phone and the other device.)

• To interrupt the search, press Stop. The device list freezes and you can start to form a connection to one of the

devices already found.

If you have searched for devices earlier, a list of the devices that were found previously is shown first. To start a new

search, select More devices. If you switch off the phone, the list of devices is cleared and the device search needs to

be started again before sending data.

4. Scroll to the device you want to connect with and press Select. The item you are sending is copied to Outbox and

the note Connecting is shown.

5. Pairing (if this is not required by the other device, proceed to step 6.)

• If the other device requires pairing before data can be transmitted, a tone sounds and you are asked to enter a

passcode. • Create your own passcode (1-16 characters long, numeric) and agree with the owner of the other device

to use the same code. This passcode is used only once and you do not have to memorise it. • After pairing, the

device is saved to the Paired devices view.

6. When the connection has been successfully established, the note Sending data is shown. Data received via

Bluetooth can be found in the Inbox folder in Messaging. Tip: Pairing is a means of authentication. The users of the

devices using Bluetooth technology should agree together what the passcode is, and use the same passcode for

both devices in order to pair them. Devices that do not have a user interface have a preset passcode.

Checking the status of the Bluetooth connection

• When the Bluetooth icon is shown in standby mode, Bluetooth is active.

• When the Bluetooth icon is blinking, your phone is trying to connect to the other device. • When the Bluetooth icon is

shown continuously, the Bluetooth connection is active.

Receiving data via Bluetooth

When you receive data via Bluetooth, a message alert tone is played and you are asked if you want to accept the

message. If you accept, the item is placed in the Inbox folder in Messaging.

Disconnecting Bluetooth

A Bluetooth connection is disconnected automatically after sending or receiving data.

Hope it helps .

Fill free to pass your comment.

Thanks for using fixya...

hey hi...may b i can solve ur problm...

you cannot send or receive data on the iphone via the bluetooth, the bluetooth is only to use with devices like hands free

sorry

nick

When you are receiving the file, check whether you have checked the Visible to other option. And it will ask for the confirmation when you will be receiving the file from other phone whether to accept or not. While sending the phone to which you are sending data should accept the file you are sending.

Let me know if you have any comments.

hi thanks for using fixya!

Please follow the instructions below:

1. Tap Start Menu
2. Tap Settings Menu
3. Tap to got to Connections Menu
4. Tap Beam, and tick the "Receive all incoming beams", then close it
5. Go to the Bluetooth, you must add new device, make sure that your bluetooth is turned on and the other device must be turned on and visible for you to search it.
6. And there you go, just follow the next steps from your pda and you will be able to send and receive datas via bluetooth.

If you need further assistance, let me know!

Don't forget to rate me positively! thanks!

just turn on the wifi or bluetooth switch in both device. after select the data which you want to send,right click > send > via bluetooth > search device > select the device > next > give pass word.. eg.0. > next> send>

in mobile you can see accept option. just select it,give pass word that you will give in your computer... eg.0 > and accept.

hi thanks for using fixya!!

Please check the Bluetooth Settings, then select Mode, you should tick the "Make this device visible to other devices".

Then, select BEAM, then tick "Receive all incoming beams" to enable you to receive datas via bluetooth.

Then, make sure you have enough spaces to your internal memory and external SD card.

Hope this will help, let me know if you need further assistance.

Don't forget to rate me with my simple solution. Thanks!

it will not show u sending via bluetooth but it sends as beaming the file