Question about Electrical Supplies

1 Answer

My kipor KGE 1000Ti starts fine but after several minutes stops generating and the red overload light comes on, with the demand for power left connected and the generator still running electrical generation will restart within a short time and the overload light is extinguished, before the whole cycle of generation and lack of output starts all over again. The green light remains on throughout. This fault is apparent with or without the smart switch on, I have checked the stepping motor and this seems fine. This fault does not seem to appear in the shop manual I am only operating a small tv and decoder in my motorhome, so do not beieve that i am actually overloading the generator David B

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 5,603 Answers

You may be UNDERLOADING the generator and it may be unstable with such a light load... see if it might behave running a heavier load... put a 100 watt light on it as a test,

Posted on Jul 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My kipor KGE 6000 Ti generator overload light is on, and there is no current output.


Read the instruction manual. If you are certain you did everything right and the generator does not behave as intended then return it to the supplier as faulty.

Jan 27, 2018 | Kipor Electrical Supplies

1 Answer

Kipor KDE12sta generator under/over voltage LED burning, the engine stops after a few seconds


hi
this happens when voltage regulator is at fault .
what happens is that the demand out put is ( volts /amps too high ) and engine power is too low causing engine to stop renew or service voltage regulator

Nov 12, 2017 | Kipor Electrical Supplies

1 Answer

Yamaha 2400IS Generator goes to overload when ie: 240 volt plugged in, or 700 watt angle grinder plugged in.


No idea but somebody else will probably come along with a better idea then mine, seems a lot of these generators have this thing installed on them (Has $25 hard start kit). Not sure what it does or how it works. Strangely enough you said you use it for 240 volt. Looked at the picture and didn't see a 240 volt connection.
If you are using the what look like the 120 volt circuits you can't over load the unit. Maximum current draw will cause it to go into protection mode and shut down the power load. The following is an exert from the owners manual which I got from Yamaha's site. Link at the end of this post.

Hope this helps


-
16
-
q
760-029
AE00788
Overload indicator light
The overload indicator light
1
comes on when an over-
load of a connected electrical device is detected, the
inverter control unit overheats, or the AC output voltage
rises. The electronic breaker will then activate, stopping
power generation in order to protect the generator and
any connected electric devices. The AC pilot light
(green) will go off and the overload indicator light (red)
will stay on, but the engine will not stop running.
When the overload indicator light comes on and power
generation stops, proceed as follows:
1. Turn off any connected electric devices and stop
the engine.
2. Reduce the total wattage of connected electric
devices within the application range.
3. Check for blockages in the cooling air inlet and
around the control unit. If any blockages are found,
remove.
4. After checking, restart the engine.
http://www.yamahamotorsports.com/assets/service/manuals/0/LIT-19626-01-23_1423.pdf

Jun 06, 2016 | Yamaha EF2400iS Portable Generator

2 Answers

The generator starts but when i plug in something it overloads with only one thing plugged in and stops generating


what watt is the jenny and what whatt is the tool ur using are u drawing to much power ?

Oct 09, 2013 | Kipor Kge3500ti

1 Answer

My kipor KGE 6000 Ti generator overload light is on, and there is no current output


Speak to us and we can help you diagnose this error.

www.generatorguru.com

Dec 25, 2012 | Electrical Supplies

1 Answer

Kipor ig6000 overload alarm


most warning and alarm's are set less than what the manufacture rating is. it's a safety feature without it we would overload all our stuff

Sep 23, 2012 | Kipor Electrical Supplies

Not finding what you are looking for?
Electrical Supplies Logo

Related Topics:

1,441 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electrical Supplies Experts

Gene Haynes

Level 3 Expert

5353 Answers

Brad Brown

Level 3 Expert

18108 Answers

john h

Level 3 Expert

22400 Answers

Are you an Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...