Just moved my precor c966i treadmill (we disassembled it down to the motor/treadmill part) and can't remember where the gray snap-in electronic connector that runs from the console down to the motor and electronics housing. Can you help me?

To clear the error log, press "QUICKSTART" for a minimum of four seconds while viewing the list. Prompts will appear on the display and let you know when the log has been deleted.
https://www.sportsrec.com/reset-error-code-precor-treadmill-5519820.html

https://www.youtube.com/watch?v=_yD5eoMNB64

20 Most Recent Precor 956I Experience Treadmill Questions ...
Apr 12, 2012
20 Most Recent Precor 9.33 Treadmill Questions & Answers
Apr 12, 2012
20 Most Recent Precor 932i Treadmill Questions & Answers
Apr 11, 2012
20 Most Recent Precor C966i Treadmill C 966i Questions & Answers
Apr 25, 2010
More results from www.fixya.com

c966 have Precor transported from one place to another place is not rash to give any signal in transcri could you help

Replacement Parts for Fitness Exercise Equipment at SPORTSMITH

I am not sure where you can find a used one, but I can find a couple of new options for you. Depending on your machine, there are two different motors available. One is for a 220V machine and the other is for 110V machine. I will post links to both.

MOTOR LIFT ACTUATOR 120V PRECOR TREADMILL PPP000000044257107 SPORTSMITH net

Lift Motor 240V Precor PPP000000044257108 SPORTSMITH net

Precor Error 15, AC Input Voltage Too High Probable Cause 1. AC input voltage is incorrect.
2. AC input voltage transients. Transients can be caused by lightning strikes or by other pieces of equipment sharing the unit's AC power.
Corrective Action

1. Verify AC feed into the building's circuit breaker is correct and connected to the proper transformer tap.
2. Ensure the AC grounding for the unit's outlet is good and verify the unit is connected to an isolated and dedicated 20 amp circuit.

Precor Error Code 15

see the video and lube the deck belt+rollers bearing too.
Tight the drive belt motor.
test the motor see the diagram and go to my personal tips for motor helps.
God bless you

LUBE OR wax you deck belt, this happen for autoprotection electronic system. To due a lack of LUBE maintenance schedule.Do it right now according with owner manual.
2)lube THE rollers bearings too use WD-40 for the bearings only
3) Test the drive belt motor, for cracking or worn belt, replace or adjust in according.
4) Test the motor voltage input, if there are the motor need repair, see my personal TIPS for troubleshooting.
5) Test the output voltage board, for input voltage motor, if there are NOT the board is faulty.
God bless you

LUBE or wax the deck belt, this happen because you do not lube or wax your equipmente according with the schedule maintenance, you must do it, every week. Do it now.use 100% silicone lube-
2) LUBE the rollers bearing too use WD-40 for rollers b only.
3) Test the drive belt motor, and adjust it or replace
4) test the input voltage motor, if there are the motor need repair.see my personal TIPS for troubleshooting helps.
5) test the output voltage board, for input voltage motor, if there are NOT the board is faulty. see the block diagram
God bless you

Dear Sir:

I will help you , inmediately.

This problem is normally by the use. Go to radio Schak , and buy some Spray for to clean and lubricate electronic parts, contacts, buttons , or Spray for clean to pressure.


This will be fix it this problem.

Thank you in advance,sincerely. God bless you.

If you need further assistance please reach me.

E.CUADRA
MANAGUA, NICARAGUA. C.A.

Error 22 means the drive motor is diconnected. you will hear the fan and other parts make noise but check the red and black anderson connection between the main circuit board and motor.