Question about Vizio GV42L 42 in. LCD Television
I turn the tv on.....I get a blue screen that says "no signal" and then 5 seconds later the TV turns off. Pressing the menu or input button does nothing.
I fear it could be the main board. What are your suggestions?
Just hold down the input button on the right side of the tv. This is the bottom one. So,
With the tv off,
press and hold the bottom button (input)
when the tv turns on, and you see the input menu
release and press the button to put the tv into a mode that works!
Posted on Jan 11, 2009
FIX FOR THE BLUESCREEN NO SIGNAL PROBLEM: without powering the TV on, hold down the input button and it will reset the signal :) you should see the TV power itself on once it resets... hope this helps.
Posted on Jul 18, 2008
I just 10 minutes ago got done solving this problem. All together, I spent about an hour before I got it to work. A blue screen would come up with "no signal" indicated and then the tv would power off after 2 or 3 seconds. I first called vizio tech sup. and they weren't able to fix it. According to the ts guy, this happens when you press "input rgb" and don't have a computer attached to the tv. That's possible in my case because I was trying different inputs off my Harmony remote when it happened. I'm not sure which process finally fixed it, but the following are the steps I used, not necessarily in order.
--Unplug tv for 2-5 minutes. Plug back in.
--Turn tv on using remote. When it comes on, press and release "input" button several times.
--Same as above, but use buttons on side of tv.
--Turn tv on. When it comes on, press and release the input option you use to watch tv.
--When a box appears showing several input options, select the one you use to watch tv.
GOOD LUCK! P.S.--DON'T PRESS THE "INPUT RGB" BUTTON IF YOU'RE NOT HOOKED UP TO A COMPUTER!
Posted on Aug 31, 2008
My wife was bitchin and complaining about the no signal and blue screen and was about to throw the Vizio tv away. I told her to get off ur *** and hold the input button down and Poooof the TV came back on.. Now she gotta give me suckie tonight..Score!
Posted on Feb 17, 2011
Hold the "INPUT" button on the remote down while simultaneously pressing the
"POWER ON/OFF" button manually. This defeats the timer.
This is most likely a temporary solution, so please check with your warranty carrier.
J & S
Posted on Jan 03, 2009
Solution #4 got me on the right track: this is what I did to get my Vizio (42inch LCD) TV back from oblivion:
1. disconnected tv for about 5 minutes
2. turned tv on, and then HELD the "input" button pressed in for about 10 seconds without letting go. NOTE: the tv turned off as it had for days, during these 10 seconds, but....
3. The tv turned itself back on!
4. Now it's a matter of finding the right input; for me it's the "TV" input that has the signal.
--Good luck, and thanks to those that posted on this irritating issue, it saved me a bundle of cash and headaches.
Posted on Jun 09, 2011
I have the 32" version. Pressing input alone did not work for me. It never turned itself on. I help it forever. Then I press "on" on the remote while holding the "input" button on the TV, and that worked right away.
Posted on Nov 22, 2009
I got the same problem and solved it. Basically the "RGB" Input is tripped.
To solve this, you will need a computer with a serial port and RS 232 serial cable (to connect the TV RGB port and the computer).
1. Connect the computer to the TV RGB port (located in the rear panel connections) using the RS 232 serial cable.
2. Turn On the computer.
3. When the computer has powered up (you see the computer desktop), turn on the TV and before the it turns off, set the computer in Presentation Mode (you will be able to see the computer desktop on the TV screen).
4. The TV now does not turn off and you will be able to use the remote control to set the Input mode in "TV".
Hope this fix your problem.
Posted on Oct 13, 2008
I had this problem on my Vizio VO22L. It was giving me a "No RGB Signal" "The Power Will Be Turned Off" message when I had it in RGB mode (with VGA input from my PC). Anytime I left my PC on and turned off, then turned on the power of this unit, I got this message. I just got off the phone with a very friendly and patient Tech Support woman at Vizio, who talked to several different techs who all came up multiple things that didn't work or help. Finally, while we were talking, she came up with the idea of going into the settings menu and doing a "System Reset" to see what happens. What do you know, it worked!
To anyone else having this problem, try this. With the PC and TV on, in RGB mode, go into the menu screen with the remote (could also be done in TV mode). The far right tab is "Setup". Use the arrow keys to go down to the "System Reset" option. When prompted "are you sure" select "Yes". I powered the monitor off and on, and the problem is gone. Now if it happens again, I know what to do.
Posted on Jul 14, 2009
Thanks for this fix. Saved me from having to buy a new tv...my husband was out the door to go get one when I found this on-line. Blue screen no signal two days multiple phone calls to vizio and cable company no help. Thank you all.
Posted on Oct 09, 2010
I tried unplugging the power for several minutes as well as swapping inputs, including from a laptop. Solution #3 is actually what worked. It is as easy as pressing the input button on the side of the TV. When the set clicked on, the familiar input menu was there in place of the blue "no signal" screen.
Posted on Oct 12, 2009
I had the same problem. I bought my VA26L at Sam's Club marked "Coaxial doesn't work" for $164.00. After reading this blog, I tried holding the "Input" button with no success. I then went into the menu and had the TV scan for channels. It found the channels on my antenna and took off. Hope this helps someone else. Thanks.
Posted on Sep 05, 2009
Turn on everything.
press the FN BUTTON AND F7( LCD) ON UR LAPTOP.
THEN FROM THERE, U WILL SEE UR OPTIONS.
IT WORKED FOR ME.
HOPE THIS HELPS.
Posted on May 11, 2010
I have my Vizio hooked to cable box, and I get "no signal" blue screen, too. I got help via Verizon and cable co. IF you have yours connected to cable when the "no" comes on, take the power cord out of the back of cable box, wait about a minute and re plug. The cable box will display an odd bunch of lines where the time and channel are displayed on front, it's working on reconnection. It should re -program itself, but if not, just turn cable box off with remote and then back on. The cable pic should appear again. This helped my "no signal" problem when I was just trying to watch cable and it wouldn't show. Good luck.
Posted on Mar 22, 2009
It Works THANK YOU VERY MUCH JOHN
Posted on Oct 03, 2008
This tv is a piece of sheet, the blue screen probelm is not solvable and happens all the time. no tv for me today, glad i spent all that money.
Posted on Nov 23, 2008
For My VIZIO
- - - - - - - - - - - - - - - - - - - - - - -
To Fix VIZIO ... No Signal ....
..... When TV OFF ...
Hold Down 2 Buttons .... MENU + INPUT ....
Power will ON ...
Change INPUT quickly within 3 Sec.
.... to HDMI or Others ...
- - - - - - - - - - - - - - - - - - - - - - - -
Posted on Apr 29, 2017
You should try resetting your TV back to factory reset. Press down the mute, 1, 8, 2 and power on using the remote.
Posted on Sep 03, 2015
I tried for about 45 minutes, couldn't figure this out! Finally, I called my husband into our bedroom, then he too began pushing the buttons. Then I said , let me google this. Low and behold, It directed me to your site. I did exactly as "seemo" suggested, it worked! Thanks so much!
Posted on Dec 01, 2014
Wow... it worked for me, too.. the technician i spoke with said some blah-blah module was burned out and that may have affected the blah-blah converter. "I Just saved a bundle on my TV repair."
Posted on Jan 28, 2013
My vizio brought up blue screen saying HDMI no longer ??? then some letters lxsoloxys??? then press exit . now tv black screen and nothing coming up. plzzz help
Posted on Jul 30, 2012
Had the same problem after screwing around with the "New" remote the Vizio GV42L went to "No signal" and shut off. I went to bed sick to my stomach,when I woke up I came to this site,got the info and I tried the Hold the input button while the TV is off and it worked again...thank you guys and Fix Ya for the help!!!!
Posted on Dec 26, 2011
Ok i was watching a dvd in the dvd player i turned it off then swiched to tv i saw a pic then it went to blue screen no signal wtf? did i do plzz help ty
Posted on Aug 25, 2010
Great site! My husband thought we were going to have to choke up more money to buy a new tv on Christmas! We connected the tv to our laptop with the RGB cable and changed the input. My 3 yr old had pressed the RGB input when he was trying to be helpful and turn off the tv. Thanks again for the suggestions.
Posted on Dec 24, 2010
That works for me too should i get ready to git rid of?????
Posted on Jan 01, 2010
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Tips for a great answer:
Sep 29, 2012 | Vizio GV42L 42 in. LCD Television
Oct 09, 2010 | Vizio GV42L 42 in. LCD Television
Feb 21, 2010 | Vizio GV42L 42 in. LCD Television
Feb 09, 2010 | Vizio L42HDTV 42 in. LCD Television
Apr 23, 2009 | Vizio Gallevia GV42LF 42 in. LCD...
Sep 08, 2008 | Vizio P50HDTV10A 50 in. Plasma HDTV
Oct 15, 2007 | Vizio P2 42 in. HD-Ready Plasma Television
57,353 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: