Cruise control is on but will not set speed - MTX Dodge Ram Quad Cab 2002-2003 Thunderform, Loaded with Dual 10 Inch Subs and Amplified, Charcoal Car Speaker

step 1
Remove the left sound insulator
step 2
the stop switch is here, way way up top
use flash light to see it.
it is there.
top of pedal it is there. SM books step1.

buy the service manual.?
if the switch ever sticks on , cruise ENDS
it is a NO, switch normally open contarts
no calibration is stated so its PnP

Which engine ?
Cruise Control Description and Operation (3.6L)
Cruise Control Description and Operation (3.4L)

Do you know what all is involved in C.C. operation ?


Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions at speeds above 40km/h (25 mph). However, steep grades may cause variations in the selected speeds. The main components of the cruise control system are:
• The cruise control module assembly
• The cruise control switches
• The cruise control release switch
• The powertrain control module (PCM)
• The stoplamp switch assembly
• The vehicle speed sensor


The cruise control module controls the operation of the cruise control system. The cruise control module monitors the signal circuits of the cruise control switches. When the normally open cruise On/Off switch closes with a switch activation, the cruise control modules detects a high voltage on the signal circuit. The cruise control module activates the cruise control system.The set/coast switch and the resume/accel switch will not operate the system when the cruise control module has not activated the system based on the cruise control on/off switch signal circuit .
The cruise control module monitors the cruise control set/coast switch in order to determine when to capture and maintain the vehicle speed. The cruise control module monitors the vehicle speed signal circuit in order to determine the desired speed. The PCM pulses the vehicle speed signal circuit at 4000 pulses per minute. After an initial set speed has been established, the cruise control module also uses the cruise control set/coast switch signal circuit in order to tap down the set speed when the cruise control module detects a switch activation.
The cruise control module monitors the cruise control resume/accel switch signal circuit in order to determine when to resume the previous set speed. This feature only works within the same ignition cycle and as long as the cruise wasn't turned off using the cruise control On/Off switch since the last cruise engagement. After the set speed has been resumed, the cruise control module also uses the cruise control resume/accel switch signal circuit in order to tap up the set speed when the cruise control module detects a switch activation.
The cruise control module assembly has a controller and an electric stepper motor to vary the throttle in each different cruise control mode. Two components in the module assembly help to do this. The electronic controller and the electric stepper motor. The controller monitors vehicle speed and operates the stepper motor. The stepper motor operates in response to the controller, to maintain the desired cruise speed. The electric stepper motor moves a strap that is attached to the cruise control cable which moves the throttle

brake control switch ???? Define brake control switch ? Do you mean the switch on top of the brake pedal ? Brake light switch ? bake symbol stays??? Assume you mean brake symbol ? This is why you should have taken to a qualified repair shop. You probably have no idea as to how the cruise works . Your vehicle's cruise control is computer controlled . Vehicle has electronic throttle control , do you know what that is ? Before i get to technical , is the air bag light lit on the instrument cluster ? When you turn on the cruise does the cruise light turn on ? Taking the vehicle to a qualified repair shop that has a factory or professional type scan tool an checking for DTC'S - diagnostic trouble codes should be the first step in the diagnostic process . Not guessing an replacing parts . Do or did the brake lights work before or after switch replacement ? If so the switch wasn't bad.

The body control system consists of the body control module (BCM), communications, and various input and outputs. Some inputs, outputs and messages require other modules to interact with the BCM. The BCM also has discrete input and output terminals to control the vehicle's body functions. The BCM is wired to the GMLAN high speed serial data buss and the GMLAN low speed serial data buss and acts as a gateway between them. If the BCM does not communicate the vehicle will not start due to the inability of the engine control module (ECM)/powertrain control module (PCM) and theft deterrent module (TDM) to communicate without the BCM providing the gateway function.

Cruise Control Description and Operation
Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions at speeds above 40 km/h (25 mph). Steep grades may cause variations in the selected vehicle speeds.
The following are the main components of the Cruise Control System:
• The accelerator pedal
• The stop lamp switch
• The body control module (BCM)
• The cruise control switches
• The engine control module (ECM)
• The throttle actuator control (TAC) motor
• The vehicle speed sensor (VSS)

The body control module (BCM) monitors the signal circuit of the cruise control switches. The BCM relays the cruise control switch status to the engine control module (ECM) via the GMLAN serial data circuit. The ECM uses the status of the cruise control switch to determine when to capture and maintain the vehicle speed. The ECM monitors the vehicle speed signal circuit in order to determine the desired vehicle speed. The ECM uses the throttle actuator control (TAC) motor in order to maintain the vehicle speed. For further information on the TAC System, refer to Throttle Actuator Control (TAC) System Descriptionfor the 4.3L engine or Throttle Actuator Control (TAC) System Description for the 4.8L, 5.3L, 6.0L, 6.2L or 7.0L engines.
Voltage is supplied to the cruise control switch via the steering wheel control switch reference voltage circuit supplied by the BCM. The cruise control function switches are arranged in a resistive ladder design, with each cruise control function switch having a different resistance value. The BCM detects a specific voltage value that is associated with the cruise control function switch being activated. When the normally open cruise control on/off switch is turned ON, the switch closes and the BCM supplies a ground to the cruise control switch ON indicator circuit as it becomes illuminated. The BCM sends a GMLAN serial data message to the ECM indicating that the on/off switch is active. Similarly, when the normally open + RES switch or the normally open - SET switch are pressed, the switch closes and the BCM detects the predetermined voltage signal on the cruise control set/coast and resume/accel switch signal circuit. The BCM sends a GMLAN serial data message to the ECM indicating that the + RES switch or the - SET switch is active. To engage the Cruise Control System, ensure that the vehicle speed is above 40.2 km/h (25 mph), turn the cruise On/Off switch ON and momentarily press the - SET switch. The ECM will engage the Cruise Control System and record the vehicle speed. The ECM sends a GMLAN serial data message to the driver information center (DIC) in order to illuminate the CRUISE SET TO ### message. The ECM sends a GMLAN serial data message to the instrument panel cluster (IPC) in order to illuminate the Cruise Engaged indicator in the IPC. The - SET switch and the + RES switch will remain inactive when the BCM has not received the predetermined voltage signal from the on/off switch. Pressing the accelerator pedal, while the Cruise Control System is engaged, will allow the driver to override the Cruise Control System in order to accelerate the vehicle beyond the current set vehicle speed. When the accelerator pedal is released, the vehicle will decelerate and resume the current set vehicle speed. The driver can also override the current set vehicle speed via the - SET switch and the + RES switch. When the Cruise Control System is engaged, pressing and holding the - SET switch will allow the vehicle to decelerate from the current set vehicle speed without deactivating the Cruise Control System. When the - SET switch is released, the ECM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the Cruise Control System is engaged, momentarily pressing the - SET switch will allow the vehicle to decelerate at 1.6 km/h (1 mph) increments for each time that the - SET is momentarily pressed, with a minimum vehicle speed of 37 km/h (23 mph). Pressing and holding the + RES switch, when the Cruise Control System is engaged, will allow the vehicle to accelerate to a greater vehicle speed than the current set vehicle speed. When the + RES switch is released, the ECM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the Cruise Control System is engaged, momentarily pressing the + RES switch will allow the vehicle to accelerate at 1.6 km/h (1 mph) increments for each time that the + RES switch is momentarily pressed, with the maximum acceleration total of 16 km/h (10 mph) over the current set vehicle speed. Momentarily activating the + RES switch will recall the previous vehicle speed, after the cruise control system is disengaged by pressing the brake pedal or by activating the CANCEL switch.

Very highly doubtful that you could fix this .

It's probably a problem with cruise control module , located under the hood in engine compartment . Or a bad connection somewhere . Do you know how to do electrical testing ? Is the air bag light lit on the instrument cluster ?

Could have DTC'S - diagnostic trouble code's stored .
DTC P1554
The powertrain control module (PCM) inhibits cruise control operation when certain conditions are not appropriate for cruise control operation. The PCM removes the ground from the cruise control inhibit signal circuit in order to disengage cruise control operation.
DTC P1585
Output driver modules (ODMs) are used by the powertrain control module (PCM) in order to turn on many of the current driven devices that are needed to control various engine and transaxle functions. DTC P1558 set indicates that an improper voltage level has been detected on the signal circuit which controls the cruise control inhibit circuit.
Action Taken When the DTC Sets
• The PCM will not illuminate the malfunction indicator lamp (MIL).
• The PCM will store the conditions present when the DTC set as Failure Records data only.

Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions. However, steep grades may cause variations in the selected speeds. The electronic cruise control system has the capability to CRUISE, COAST, RESUME SPEED, ACCELERATE, and TAP-UP or TAP-DOWN.
The main parts of the cruise control system are:
• The cruise control module assembly
• The function control switches
• The cruise control release switch
• The clutch pedal position switch (CPP), if equipped
• The stop lamp switch assembly
• The vehicle speed sensor
The cruise control system uses the cruise control module assembly to maintain the desired vehicle cruise speed and operation. The cruise control module assembly has an electronic controller and an electric stepper motor to vary the throttle in each different cruise control mode. The electric controller monitors vehicle speed and operates the electric stepper motor. The stepper motor operates in response to the electronic controller, to maintain the desired cruise speed. The electric stepper motor moves a strap that is attached to the cruise control cable which moves the throttle linkage. The cruise control module assembly contains a low speed limit which will prevent system engagement below a minimum speed of 40 km/h (25 mph). The module assembly is not serviceable.

It is HVAC 1fuse #39 in the rear fuse block ,this powers the on/off switch for cruise control ! Fuse Block - Rear Beneath the left rear seat. What engine does it have ? 4.2 L or 5.3 l There is no vacuum involved in the operation of the cruise control ! Your vehicle has electronic throttle control .
Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions at vehicle speeds above 40 km/h (25 mph). Steep grades may cause variations in the selected vehicle speeds.
The following are the main components of the Cruise Control System:
?€¢
The powertrain control module (PCM)

?€¢
The On/Off switch

?€¢
The Resume/Accel switch

?€¢
The Set/Coast switch

?€¢
The TCC brake switch

?€¢
The stop lamp switch

?€¢
The throttle actuator control (TAC) motor

?€¢
The vehicle speed sensor

Cruise Control Engaged
The cruise control system will engage and adjust the vehicle speed based on the activation of the following cruise control switches:
?€¢
On/Off

?€¢
Resume/Accel.

?€¢
Set/Coast

The cruise control switches are located on the multifunction/turn signal lever.
The powertrain control module (PCM) monitors the signal circuits of the cruise control switches in order to determine when to capture and maintain the selected vehicle speed. The PCM uses the throttle actuator control (TAC) module motor in order to control the vehicle speed. For further information on the TAC System, refer to Throttle Actuator Control (TAC) System Description in Engine Controls - 4.2 L.
Ignition positive voltage is supplied from the 10 ampere HVAC 1 fuse to the cruise control switch via the ignition 3 voltage circuit. When the normally open cruise control On/Off switch is turned On, the switch closes and the PCM detects a high signal voltage on the cruise control on switch signal circuit. When the normally open Set/Coast switch is pressed, the switch closes and the PCM detects a high signal voltage on the cruise control set/coast switch signal circuit. To engage the cruise control system, turn the On/Off switch On and momentarily press the Set/Coast switch. The PCM will confirm that the cruise control enable criteria has been achieved. The PCM will engage the cruise control system and record the selected vehicle speed. The PCM sends a class 2 message to the instrument panel cluster in order to illuminate the cruise control indicator. Pressing the accelerator pedal, while the cruise control system is engaged, will allow the driver to override the cruise control system in order to accelerate the vehicle beyond the current set vehicle speed. When the accelerator pedal is released, the vehicle will decelerate and resume the current set vehicle speed. The driver can also override the current set vehicle speed via the Set/Coast switch and the Resume/Accel switch. When the cruise control system is engaged, pressing and holding the Set/Coast switch will allow the vehicle to decelerate from the current set vehicle speed without deactivating the cruise control system. When the Set/Coast switch is released, the PCM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the cruise control system is engaged, momentarily pressing the Set/Coast switch will allow the vehicle to decelerate at 1.6 km/h (1 mph) increments for each time that the Set/Coast is momentarily pressed, with a minimum vehicle speed of 37 km/h (23 mph). When the normally open Resume/Accel switch is activated, the switch closes and the PCM detects a high signal voltage on the cruise control resume/accel switch signal circuit. Activating and holding the Resume/Accel switch, when the cruise control system is engaged, will allow the vehicle to accelerate to a greater vehicle speed than the current set vehicle speed. When the Resume/Accel switch is released, the PCM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the cruise control system is engaged, momentarily activating the Resume/Accel switch will allow the vehicle to accelerate at 1.6 km/h (1 mph) increments for each time that the Resume/Accel switch is momentarily activated, with the maximum acceleration total of 16 km/h (10 mph) over the current set vehicle speed . Momentarily activating the Resume/Accel switch, after the cruise control system has been disengaged by pressing the brake pedal, will recall the previous set vehicle speed that is recorded in the PCM.

Bummer deal! This may be a way to tell you some tail lights are burnt out. Some cruise controls have a fuse in a second location.
The fuse is not in right or is blown. Check with a new fuse. Hope this helps. ...gc http://www.auto-tune-up-and-repair-options.com/

Cruise Control
Any given speed above approximately 22 mph (35 km/h) can be maintained with the cruise control by operating the lever.
-see photo

1. Accelerate and set: Lift lever briefly to set speed. Hold lever up to accelerate.
2. Decelerate and set:
   Depress lever briefly to set speed. Hold lever down to decelerate.
   Normally the vehicle is accelerated to the desired speed with the accelerator. Speed is set by briefly pushing
   the lever to position 1 or 2. The accelerator can be released. The speed can be increased (e.g. for passing)
   by using the accelerator. As soon as the accelerator is released, the previously set speed will be resumed automatically. If a set speed is to be increased or decreased slightly, e.g. to adapt to the traffic flow, hold lever in position 1 or 2 until the desired speed is reached, or briefly tip the control lever in the appropriate direction for increases or decreases in 0.6 mph (1 km/h) increments. When the lever is released, the newly set speed remains.
3. Canceling

To cancel the cruise control, briefly push lever to position 3.
When you step on the brake or the vehicle speed drops below approx. 22 rnph (35 km/h), for example when driving upgrade, the cruise control will be canceled.
4. Resume
If the lever is briefly pushed to position 4 when driving at a speed exceeding approx. 22 mph (35 km/h), the vehicle resumes the speed which was set prior to the cancellation of the cruise control. The last memorized speed is canceled when the key in the steering lock is turned to position 1 or 0.
Note:
If the engine does not brake the vehicle sufficiently while driving on a downgrade, the speed you set on the cruise control may be exceeded and you may have to step on the brake pedal to slow down.
As soon as the grade eases, the cruise controlled speed will again be maintained as long as the brakes were not previously applied, or the lever may be used to resume the previously set speed if the brakes were applied.


http://www.benzworld.org/forums/attachments/w202-c36-c43/153145d1197313761-pdf-owners-manual-w202-1995-2000-1999-c280_owners_manual.pdf

If you know how to set your speed limiter. To set your cruise control, press the stalk in (to the right). The orange light on your dash should go out and you're ready to set your cruise control. You can start the cruise control by either moving the cruise control stalk up or down. Once you start the cruise control you can move the stalk up or down to increase or decrease your cruise speed. You can move it toward you to shut off the cruise control. You can press it in again to go back to the speed limiter. I hope this helps.

Here are the steps in using cruise control:

1. Get on a road you will be traveling at the same speed for a long period of time, such as a freeway.
   
2. Reach your desired speed. Choose a speed that allows you to move with the flow of traffic and not go over or under the designated speed limit for that road.
   
3. Locate the ON and SET buttons on your steering wheel. Press ON first and SET after. Your cruise control is now activated. Most vehicles must be traveling at least 30 miles per hour to set the cruise control.
   
4. Press and hold the SET button if you wish to use cruise control at a higher speed. Hold until your desired speed is reached.
   
5. Decrease speed by pressing the COAST button.
   
6. Push the brake pedal to disengage the cruise control function. If you wish to return to the previous set speed, use the RES (resume) button. You must be traveling at least 30 miles per hour for this function to resume.
   
7. Erase any previous speed by pressing the OFF button.