Ice maker won't work

if you dont use an ice maker much they can freeze up i left my full for a month and it froze back to the water supply i dumped the ice and cut of water to the ice maker then thawed it out hooked back up and fine

you need to replace the ice maker because the heater inside the ice maker is broken thats way its not ejecting the ice

Faulty door seal.The seal that holds the door has a grip and a magnet on other side.May be that needs to be replaced.Or any fringe section tray is not completely fitted,to its end causing these.

Replacement parts can be purchased at any of the following web sites:

searspartsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com

partsselect.com

--------------------

Before going to buy any parts directly.
Go through this troubleshooting help links.

-------------------------

This is list of refrigerator problems, which is normally faced in refrigerator.
You can go through the details, by clicking the link below:---

--------------
Refrigerator is not cooling properly?
http://technoanswers.blogspot.com/2011/06/refrigerator-is-not-cooling-properly.html
-----------
Both refrigerator and freezer not cooling properly in refrigerator?
http://technoanswers.blogspot.com/2011/06/both-refrigerator-and-freezer-not.html
----------
The ice maker not working: ---
http://technoanswers.blogspot.com/2011/06/ice-maker-stopped-working.html

------------
Compressor not running on refrigerator?
http://technoanswers.blogspot.com/2011/10/compressor-not-running-on-refrigerator.html
--------
Water dispenser not working on refrigerator?
http://technoanswers.blogspot.com/2011/10/water-dispenser-not-working-on_19.html

-------------

Ice maker stopped making ice?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-stopped-making-ice.html

-------------

Water Overflows in Ice maker and freezes inside?

http://alltypesofpartsreplacing.blogspot.com/2011/10/water-overflows-in-ice-maker-and.html

-------------

How to replace Ice maker assembly?

http://alltypesofpartsreplacing.blogspot.com/2011/10/how-to-replace-ice-maker-assembly.html

These will help.

Thanks,.

There should be a plastice hinge cover on the left top hinge on freezer door. Take it off and press the plug together firmly. Try that and let me know, Sea Breeze

OK, that should be no problem. Test your ice maker and fill with water if empty of ice. If full of ice and not moving to dump tell me. I need to help you locate the problem doing that and answering will tell me the problem. Also look around the door frame and inside for the model Profile that you have. and get back with me as soon as possible, Thanks Sea Breeze

Icemaker is in line with the water and runs from the icemaker threw the door and up to the water valve. So that is why the ice maker is working and the water is not working, most likely the water has frozen inside, And this can be caused by many different reasons, if it has been humid or the door was left open then shut it would cause the moisture in the air to be drawn to the warm water and flash frosted the pipe, try to see if you can defrost the line with a hair dryer. If that does not work post here and I will tell you the next step to try.

water valve or icemaker or make sure freezer is freezing check see if you have frost build up

yes repl the water valve at the back of unit but first i need you to get an insulated wire strip the endes of it and remove front cover from ice maker lookt for th letter t and h insert the wire inside the holes and look at the ejector inside mold is it starts moving let it finish cycling it no water repl valve if it does not move repl module but is better or ice maker alomost same price

Had the same problem. The water line from the valve to the ice maker was cracked due to heat from the compressor.

There is no pump per say.. the water pressure is all that fills the ice maker and provides water to the drinking dispensor. The solenoids are also different, one activates for ice maker and the other for drinking water. The fastest way to check water flow is to swap the wires on the solenoids so the drinking water "power" will now power the ice fill solenoid. Once the plugs are swapped and you press the drinking water lever the ice maker should pour water out the fill tube. If that works then you know the solenoid, tube, etc. are all fine. I'd suspect then that the ice maker fill solenoid isn't getting power when it is suppose to fill. Let me know what this test result is.