Power light comes on for about 30 secs, something clicks and both power and ocp lights start blinking contineously. the screen does not light up

Sharp TV - Flashing OPC & Power Lights - YouTube

? 0:50
https://www.youtube.com/watch?v=BH1OcQ6dIEE
Jul 1, 2011 - Uploaded by Tweetssun
Sharp Aquos TV flashing a OPC & Power Lights in a pattern of 3 flashes, ... Sharp Aquos LC-32D44 - One blink lamp error - Nopicture or sound - Diagnosis ... Repairing Flat Screen TV - Blacked out with blinking red light ...Missing: 32dv22u

Sharp lcd tv power button flashing - HDTV - Streaming Video & TVs ...

www.tomsguide.com/forum/54708-4-sharp-power-button-flashing

Feb 8, 2012 - 7 posts - ‎3 authors
We have owned a Sharp 32" LCD TV for about two years. ... However a quick Bing search shows that the blinking green light usually means a bad power board, which seems ... No picture, no sound, just a black screen and two blinking green ... a cable surge block on the coax where it comes into the house. Sharp lcd tv power button flashing - Digital TV
19 posts
Oct 14, 2012
Sharp hd tv blinking power no picture - Digital TV
2 posts
Jan 7, 2012
More results from www.tomsguide.com
Missing: 32dv22u

Sharp Aquos LC 42DH77: Inverter, Backlight, Power and ...

www.normsweb.com/tektips/42dh77.shtml

Do a hard reset to this set, and check. To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. This procedure will make it a hard reset. If it do not help you, make sure that the main board is faulty. Short circuited component/s at it. Contact any service technician; or the authorized service center. In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience. If blinks continue without any pause, the main board is faulty

Try out Cisco's solution for this:

http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&login=1&app=search&vw=1&articleid=4982

good luck

Hi,
The initial Step kindly check all the lights are glowing in the Modem,If it glows then follow the below steps,

1.At the back side you will have a reset button,hold it for 30 secs and the lights in belkin router starts blinking

2.type in the internet explore 192.168.2.1,

3.Click on "Connection Type" at left side,it asks for password leave it blank and click submit

4.Select the Type as Dynamic and click on next

5.Click on Apply changes,Router gets automatically rebooted

6.Click on "MAC Address" at the left side and then click on "CLONE" and then click on Apply Changes

7.Unplug the power cable from modem and router

8.After 5 secs put the power cable only to the Modem and wait until all the lights in modem gets lit up

9.After that put the power cable to router,check you will see all the lights in the router(Modem,internet,power)

Regards,
Ayysam

I have the same problem. I can get the video by pushing the power button on top of the TV after using the remote and getting the power and ocp light dance.

helloFive blinks - AKB circuit (automatic kine bias), the timer/standby indicator blinks for about 30 seconds then goes to the self-diagnosis function. Something is wrong with the video. Check video out, Q705, 732, 761 and other components on the C board, also check Q218, 219, 220 on the A board. In addition, unit could be in IK blanking, try turning up screen slightly.

shaun

click here to find the details.

you may also like to click here

Can you tell me if the status lights on the power adapter and/or the battery turns on? Because you are telling me the status lights only stay on for 30 seconds, this should be a power connection problem.

One other possibility: can you tell me the climate environment of where you use your laptop?

The blinks can tell you the problem , is it 4 blinks that could be 3 different ics IC1509 Q1505 or IC502