Televison & Video Logo

Related Topics:

Anonymous Posted on Apr 07, 2008

Tv flashes/strobes 55 inch mistsu rear projection tv about 4-5 years old has started going black and back, not turning off, more like a strobe effect. Happens even when cable is fed directly to tv - not thru cable box. Any ideas???. This set gets pretty heavy use.

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

  • Contributor 1 Answer
  • Posted on Apr 08, 2008
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

Joined: Apr 07, 2008
Answers
1
Questions
1
Helped
52
Points
1

First - I did not send in my question when I realized yours was a pay-for service. No offence, but I generally try to exhaust all approaches I can do on my own before going to paid assistance. Yes, it probably takes more time - but my rate is pretty low (ha).

Anyway - what I did was turn off and unplug the TV, the DVR and the Cable box, and
let them all sit from the time I left for work in the morning until I got home that night, about 12 hours. When I plugged everything back in - cable box first, then DVR, then TV, if that matters - everything was working fine.

I am not sure what caused this problem to begin with. I don't think it was the cable company (Comcast) because when I disconnected the TV from the cable service entirely the set was still blinking on it's own. I guess it is possible that the cable co triggered something - but how? We did have a loss of service from them for Internet access the day before the TV problem, but the set didn't have any problem until the next day. My wife thinks it was because the kids were playing a Wii console game before the trouble began - but the kids play with the Wii often enough without any later problems.

So, the set is working OK again and I am not sure why - can't get any good info from Mitsu on the web ....oh well .... now if I could just get the darned remote to work.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

HK AVR 125 display strobing and no sound, even in headphone jack

Hi...

Find someone that does TV or audio repair and have them open it up. A cable assembly may have loosened during the MOVE.

Cheers
1helpful
1answer

My Vizio is 4 years old. Last night when we turned it on it started flashing like a strobe light. It continues to do this. What is the problem? Thank you

We need to find out the strobe effect is due to the T-CON board is turning on and off or if the backlights is turning on and off. This can also be due to unstable power supply due to bad caps.
You need to look at the back of the screen to see if the light coming through on the back side of the LCD panel is stable when the picture is strobing.
If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on:

Basic LCD monitor and TV troubleshooting guide:
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide
http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting
http://www.fixya.com/support/r7406380-tv_training_manuals
Failed TV and Monitors: http://s807.photobucket.com/albums/yy352/budm
Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague
Parts: www.shopjimmy.com
Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps.
Or www.digikey.com, just make sure to use caps with low ESR, 105c, high ripple current and long life rating such as PANASONIC FM or FC series.
Please post back what you find.
Please leave rating if it helps.
35helpful
2answers

My Vizio VX42L is flashing like a strobe light.

Mine did the same thing. Remove the stand and back of the tv. Be careful with screen do not lay on hard surface and scratch. When you take the back off you will see a board on the left side and a board on the right side. They are labeled slave and master. Remove the ribbon cables and take board out. There are 2 capacitors on each board (about an inch long). These are probably all bad (ends bulged a little with black stuff on bulged end). Radio shack has them for less than $2.00 each. turn the board over and you can read the size of the capacitor. You need someone who can use solder wick and remove all four capacitors and solder in new ones. Notice how the capacitors are turned. Each one is labeled with a dash for negative. Make sure you bend new capacitor connectors the same and put back in the same way. Put the boards back in the tv and attach all ribbon cables. Put back and stand on. hook up your power and cable box and you are ready to watch tv with no more strobe. Me, my husband, and son did ours last week. I looked up the problem on the internet, husband removed stand & back, son with the steady hand did the soldering. Family project that went well for once.
0helpful
1answer

Canon 580ex II strobe issue

This depends on the mode you have selected on the flash gun. If you have Multi selected you will get the strobe effect. The strobe effect is all so present to help the flash set the correct exposure. It's not a problem with the flash or the camera. Spend some time reading through the flash gun manual. I have to admit it is not always clear. Also try Youtube for a video.
0helpful
1answer

Philips Magnavox 42 inch plasma white strobe-like blinking

magnovox 42 inch pasma shows tv guide but does not show pciture.
7helpful
1answer

My vizio tv flashes like a strobe light

Sounds like your Backlight Inverter Board is going out, saw one on ebay for about $55 : ) have to get the one for your model tho...
1helpful
4answers

My Hayward Colorlogic pool light is flashing like a strobe light

That particular swimming pool light has a power-cycle feature that allows you to change the way your light illuminates your pool simply by turning it off and on. A strobe like effect is one of these power cycles. To change it, simply turn the switch off and then turn it back on within 10 seconds. It should reset to another cycle. It is is left off over 60 seconds, it resets to the first cycle, which could be the strobe. If cycling doesn't solve the problem, your bulb has probably malfunctioned and you are going to have to have a repair tech service it.
1helpful
1answer

My 10 year old 55 inch Mitsubishi rear projection shuts off.

The main board/switch is worn to the point it will not work anymore after a while, I been in the business for years, These are wonderful TV's, yes there are replacement parts but a quick fix your looking for here will be unsuccessful this is the reason I am providing my advice and take a chance on the rating your going to give me. Try www.ebay.com look for people that is saling parts for these TV's.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

0helpful
1answer

Swirling colors unwatchable screen RCA rear projection 52"

I will assume it does this no matter what the input is, It sounds like the board that controls the projection lamps is causing them to misfire? Or light up out of order in rapid succesion? you will probably need to have the TV serviced, or at least an estimate, so you canfigure out exactly what part has gone bad,( hard to tell sometimes when were not there), but be carefull if you decide to service it yourself.
Not finding what you are looking for?

62 views

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

Grand Canyon Tech
Grand Canyon Tech

Level 3 Expert

3867 Answers

Cindy Wells

Level 3 Expert

6688 Answers

 Grubhead
Grubhead

Level 3 Expert

5755 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...