Question about Jacuzzi RapidHeat In-Line Heater U395000 [ Bathtubs and Whirlpools,

1 Answer

RapidHeat In-Line Heater U395000 [ Bathtubs and Whirlpools,: My jacuzzi tub jets run for ONLY about 5 minutes b...

My jacuzzi tub jets run for only about 5 minutes before it stops. The other problem is it isn't really off. I have to press the button so it doesn't come back on when the tub is empty. If I'm still in the tub I can get the jets going again after about 5-10 minutes of it being off.

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Jacuzzi Master
  • 719 Answers

You have a bad motor - when a motor overheats there is a sensor inside the motor that will shut if down so as to not damage the windings and such. once your tub has cooled down for 10 mins or so it will turn back on. the fact that you can push the button multiple times just means that you are turning the air switch on the back of the motor on/off until you get to the point where the motor has cooled down and will turn back on. if you do not push the air button after the tub shuts down and you finish your bath then when the pump cools down it will come back on because the air switch in the motor is latching i.e. it is either on or off. Since you left it in the on position the motor will come back on once the motor has cooled down.

Posted on Sep 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Black particles coming out of jets


that is dirt build up in the system. run a 10 min cycle before using the tib.

Oct 13, 2013 | Jacuzzi RapidHeat In-Line Heater U395000 [...

1 Answer

Can Jacuzzi Rapid Heat inline heater be installed upside down?


You do not want to install any heater upside down because if any debris gets inside the heater pressure switch while it is running it will NOT shut off once the pump shuts off.


Rod
US Parts Center
888-521-6183

Feb 17, 2013 | Jacuzzi RapidHeat In-Line Heater U395000 [...

1 Answer

Can the U395000 inline discharge heater be used in the inlet position?


no it cannot. it is a pressure heater and must be installed after the discharge of the pump

Feb 05, 2011 | Jacuzzi RapidHeat In-Line Heater U395000 [...

1 Answer

I have the espree 536 jacuzzi tub. which heater is required for this unit. i ordered the s750000 but it is the wrong one


you will have to look to see where the fitting is to install this heater.
there are two styles of heaters they use (mostly)
In-line pressure heater that installs after the discharge of the pump but before any of the jets.
the in-line Vacuum heater installs before the front of the pump in the suction line.

Jan 16, 2011 | Jacuzzi RapidHeat In-Line Heater U395000 [...

1 Answer

The light will not come on after starting jets and the reset button has been reset. The water is hot in the tub. brand new unit


i have the same problem, checked ohm's there good at 15, why won't the rapid heat light come on letting me know t's working?

Jan 16, 2011 | Jacuzzi RapidHeat In-Line Heater U395000 [...

1 Answer

I have a new Jacuzzi tub with a Rapid In-Line Heater. When I fill the tub the water the initial temp is 67 degrees. The heater only increases the temp to 71 degrees. What is wrong with the heater ,if...


The bath heater you have is not designed to HEAT water - they only Maintain what you start with.
You need to start the bathtub with the hot water you want. It will only heat about 1-2 degrees an hour.

Jan 08, 2011 | Jacuzzi RapidHeat In-Line Heater U395000 [...

1 Answer

How do you know if a heater is compatible with your whirlpool tub?


look at the heater you have. it will say either Pressure Inline Heater or Vacuum Heater. The pressure heater installs after the pump and the vacuum heater will install before the pump in the suction line.

Dec 16, 2010 | Jacuzzi RapidHeat In-Line Heater U395000 [...

Not finding what you are looking for?
Jacuzzi RapidHeat In-Line Heater U395000 [ Bathtubs and Whirlpools, Logo

353 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jacuzzi Home Experts

US Parts Center
US Parts Center

Level 3 Expert

719 Answers

Mike

Level 3 Expert

4357 Answers

john h

Level 3 Expert

21945 Answers

Are you a Jacuzzi Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...