Hi,
My name is Dhedik, from Indonesia. I have Canon i9950 and got an error on it. Full waste ink absorber. This is same error with my other printer (Canon Pixma IP1200), but I can solve the problem using Canon printer resetter. Can you give me a link or software to solve my problem?
Regards,
Dhedik
Sorry for my bad English
Dhedik maybe this action can solved your problem
Reset Waste Ink Counter printer Canon i9950 :
1. power off Printer
2. Push and hold resume button and push power button
3. Hold Power button and release Resume button
4. Push Resume button twice ( 2x ), and now release resume button and power button
5. Green light will blinking and stop.
6. When green light on, push resume button 4 x
7. Push Power button and printer will off, if that isn't off, push power butto again until print off position.
ok good try, don't forger to vote me, Fixya
Lolz @ stevemay
you need to open it up with the clips and just absorb soem ink from the sponge that absorbs the ink. I do this to my i9950 eevry year or so and it works fine.
lolz @ stevemay
All you need to do is open up your printer (find the clips etc) with and just absorb some ink from the well (spongey bit that absorbs the ink). I do this to my i9950 every year or so and it works fine.
Sorry about the first version, I was too busy laughing at the answer from Canon :)
OK, but where are the clips?
The clips are marked with a little triangle. All you need is a flatblade screwdriver and a little force and it will unclip. The buttons at the front may also need to come out. Again they just unclip. Don't be afraid to give it a go, as the alternative is buy another machine.
×
HI,
MY NAME IS VICKY, FROM INDIA. I HAVE CANON IP 100 AND GOT AN ERROR ON IT. FULL WASTE INK TANK. BUT I CAN NOT SOLVE THIS PROBLEM
My name is Steve and I work for a Canon service company. The ink absorbers need to be replaced. However due to the size of your machine it is advisable to purchase a new machine as they are extremely difficult to change.
Eight flashes: Waste ink absorber almost full
The printer has a built-in waste ink absorber for the ink used during Print Head cleaning. Eight flashes indicates that the waste ink absorber is nearly full. Press the RESUME/CANCEL button to cancel the error so you can continue printing. Before the waste ink absorber becomes completely full, contact a Canon service representative.
Important
Canon recommends that you call for service as soon as this error occurs. Once the waste ink absorber becomes completely full, printing will no longer be possible
3,165 views
Usually answered in minutes!
When I'm printing on canon pixma ip1200 a message keeps flashing on my screen saying "ink absorber almost full". Now i can't print in that printer again. I dont know what to do
Ella
I have i9950 with similar problem. Message comes up 'Waste ink absorber almost full. Press printer's RESUME button to restart printing.' I noted that Stevemay offered an answer to a similar question that owing to the size of the machine it would be cheaper to purchase a new one - does this apply to i9950?
I cleaned the ink absorbers (all of them) but fail to reset the counter with te given instructions, I try to get into service mode but even there my i9950 gives a green light + 8 orange flashes....is there a way to manual fix this?
Reset Procedures for Canon i550, i560, i850, i860, i865, i9100, i9950 Printers Turn off Canon i550, i560, i850, i860, i865, i9100, i9950 Printers Hold down Resume button and press Power button. Keep holding down Power button and let Resume button go. Press Resume button 2 times then let BOTH buttons go. Green lights will flash and then stop blinking. When green lights are solid, press the Resume button 4 times. Press the Power button and the printer should turn off, if not, press the Power button once more. Your Canon i550, i560, i850, i860, i865, i9100, i9950 Printers should respond as normal.
×