TTY Enabled/Disabled Error

Don't know your specific unit, but in general, heating systems are two-stage devices:

1: Its too cold: the motorised HW/CH valve moved to the required position, and on achieving it, the circulaion pump starts and the boiler is enabled. (The circ pump may start immediately - its not usually important.) The hot water from the boiler circulates through the heat exchanger and/or radiators until the thermostat thinks its target is warm enough, whereupon it disables the boiler, stops the pump and closes/relaxes the valve(s).

2: The boiler is off while disabled. When enabled, it heats the circulating water to a 'high' temperature and seeks to keep it there. If it reaches that temperature, the boiler will cycle on and off as necessary to maintain the set 'high' temperature. (The circulation pump must run all the time the boiler is enabled.) This may be what you're noticing. Additionally, some boilers will run the circulation pump for a little while after being disabled to reduce the temperature if the water in the pipes and boiler.

Your question doesn't say how the pump running corresponds to thee thermostat settings, but if it were stuck on, I think you'd know!

You need the engine light issue looked into, it is likely why the system has diabled the remote start system

To verify the wireless network connection status, please go to the Network Connection Window. For Windows XP, Click on Start. Click on Run. Enter "ncpa.cpl" and click OK. For Windows 7 or Windows Vista, go to "Search programs and files" box. Enter "ncpa.cpl" and hit the Enter key.

If you see the wireless network connection icon is disabled in the Network Connections Window, you may double click on it to enable the connection. Should it is still disabled an no way to be enabled, you may have a AntiVirus software (for example, Kaspersky, ZoneAlarm, Trend Micro Internet Security...etc) installed in your computer and it disabled the wireless connection.

You may completely remove the antivirus software from your computer and restart the computer. Check the wireless connection can be enabled. Then you can re-install the antivirus software.

When you reboot your system you have to go into the bios,when you start the setup utility, the main Menu appears. the main menu of the setup utility displays a list of the options that are available. a highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. when an option is highlighted execute the option by pressing ( good luck!)
go to the [advanced setup] area
1.quick boot - enabled
2.1st boot device - disabled
3.2nd boot device change it to -cd
4.bootup numlock -on
5.aperture size -64mb or higher
6.dram timing -auto
7.auto detect dimm - enabled
8.spread spectrum -enabled
9. max cpuid value limit- disabled
10.cpu tm function- disabled
11.bios protect - disabled

2.4.2 USB Configuration
The items in this menu allows you to change the USB-related features.
Select an item then press <Enter> to display the configuration options


USB Function [Enabled]
Allows you to enable or disable the USB function.
Configuration options: [Disabled] [Enabled]
Legacy USB Support [Auto]
Allows you to enable or disable support for USB devices on legacy
operating systems (OS). Setting to Auto allows the system to detect the
presence of USB devices at startup. If detected, the USB controller legacy
mode is enabled. If no USB device is detected, the legacy USB support is
disabled. Configuration options: [Disabled] [Enabled] [Auto]
USB 2.0 Controller [Enabled]
Allows you to enable or disable the USB 2.0 controller.
Configuration options: [Disabled] [Enabled]
USB 2.0 Controller Mode [HiSpeed]
Allows you to configure the USB 2.0 controller in HiSpeed (480 Mbps) or
Full Speed (12 Mbps). Configuration options: [HiSpeed] [Full Speed]
BIOS EHCI Hand-off [Disabled]
Allows you to enable support for operating systems without an EHCI
hand-off feature. Configuration options: [Enabled] [Disabled]

NOTE!!!

Do not disable the BIOS EHCI Hand-Off option if you are running a
Windows® operating system with USB device

hope above given details with give you a detailed description as you desired.

good luck

TO FIX THE PROBLEM FOLLOW THESE STEPS:

1. Goto Recovery Menu (turn off then hold R and turn on)
2. Configuration -> Use NO-UMD (Disable it)
3. Go all the way back to main menu
4. Advanced -> Advanced Configuration -> (Disable all of them)

Configuration Should be Like This ->
.....................1. Disabled
.....................2. Enabled
.....................3. 1.50 (for Phat but needs 1.5 kernel addon) 3.80 (for Slim)
.....................4. Disabled
.....................5. Normal (Needs UMD game to play Isos) if not try Sony Np9660
.....................6. Disabled
.....................7. Enabled
.....................8. Disabled
.....................9. Enabled
.....................10. Memory Stick
.....................11. Enabled
.....................12. Disabled
Advanced->
.................Advanced configuration->
.................................................. .Disabled
.................................................. .Disabled

i hope this might help you

Hi hosington

When the word enable is shown, what it means is : it is disabled currently, by clicking on it you can enable if you wish.
Good luck
luciana44

Try this:

START/ right click Computer goto Manage/ click Services

Here are the services I have stopped and disabled. You can right click each service and goto properties to disable them.

readyboost
superfetch
print spooler - must be re-enabled and started if you use a printer
server
computer browser
secondary logon
security center
windows error reporting
windows search
windows firewall - must be re-enabled and started to use windows firewall

Hope that works, and please rate my response if it was helpful.

Thanks and good luck

has anyone gotten a solution for the problem?

siemens cell phone was working fine until my son fool around with it now the phone is saying phone disabled! phonecode now how can i get it to re-enabled its still work