Kenmore Elite 8269645: Fills between cycles

Kenmore Elite dishwasher Smart Wash light blinking
Sanitize Blinking Light
Some Kenmore dishwashers have a sanitize feature; when this light blinks, it means the sanitization step failed because the hot water in the dishwasher did not achieve the desired temperature or the final rinse cycle was interrupted.

How to Reset Codes on a Kenmore Dishwasher - Hunker

https://www.hunker.com > ... > Dishwashers
Search for: Kenmore Elite dishwasher Smart Wash light blinking
More here

https://www.applianceblog.com/mainforums/threads/kenmore-elist-665-dishwasher-smart-wash-red-light-blinking-machine-not-working.29342/


https://www.google.com/search?q=kenmore+elite+dishwasher%3F+The+smart+wash+light+blinking

Pre-wash may be compromised and a new power circuit board may be needed.
My advice: As long as the other cycles are accurate and work as usual; Pre-wash in your sink (spray off waste material) before you place the dishes in the washer and commence cleaning. Its best to wash off food and other material before washing in the machine to avoid clogging the drains and pump.

Kenmore Elite Dishwasher That Does Not Clean

I too had problems with the Kenmore Elite (aka Bosch). The issue was solved by replacing the Lock Sensor on the door. After replacing the sensor the dishwasher has been working. Hope this helps.

Hello,

Welcome to FixYa.

Can you explain more details, are you implying the unit fills with water, that it has power on the panel and you can select a cycle and nothing happens ?

Just need a little more info so i can be specific to your dishwasher.

Thanks for choosing FixYa. Please reply so we can move forward.

Regards,

Macmarkus :)

It appears your dual inlet water valve has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

sounds like wash motor is not going . it will fill and control thinks motor is working . then it will drain wash water / ( drain pump is a different motor ) and then refill and so on .. never washes but fills and drains and heats. ( look for leakage under the motor i'm sure you will find some ..

HI, the control module is damaged. this component is responsible for initiating the proper sequence. if the logic sector is damaged, it will cause these symptoms that you are experiencing.

Replace the timer or, control board asap.

Motor has gone out..just like mine...Make sure u have voltage going to the motor, (disconnect the plug from the motor) and use an electric meter to make sure you have voltage going to the motor. If so the motor has either gone out or has been blocked by something! If no noise except clicking then motor has gone out. Looking at about $150 for motor.

I have this model, but not this problem (my impeller motor seems to have burned out). Anyway, try pressing Hi Temp Scrub, Air Dry, Sani Rinse, Air Dry, in that order and see what happens. Mine appears to reset and run through a set of warm-up tests.