I assume 23 goes to 23 and 194 goes to 15b is this correct

1 Answer

Randy Parker

Contributor 17 Answers
Posted on Sep 21, 2012

Randy Parker

Contributor

Joined: Sep 20, 2012

Answers

Questions

Helped

19689

Points

That is correct

1 Related Answer

2Grumpy

5 Answers
Posted on Jan 24, 2010

SOURCE: i have a wiring question. i have a generac 5522

The generators control board senses lost utility (N1 & N2) and after a time delay kicks in the backup. The board sends 12 v to the transfer relay thru wire 194 then back to terminal 23. This is held open till the startup timer times out and only after the warmup does wire 23 close to ground. This energizes the transfer relay, contacts close and E1 & E2 can now conduct generator produced electric to the transfer relay contacts, limit switch (XB1), Wire B, and a bridge rectifier.

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

1answer

23 blinks on the lock light for latitude 2120

I am assuming you are refering to a Dell laprop, if so, that means the GPU has failed or the RAM has been dislodged/faulty.

Read full answer

Jul 16, 2023 • Cars & Trucks

0helpful

1answer

Travelinng at 40.ooo kph how long to travel 1 light year

Hopefully, I can explain this correctly.

1 light year = 9.461e+15 m
= 9.416e+12 km

I assume from your notation that you are travelling at 40 000 kph.

40 000 = 4.000e+5

Now we have everything in the same units, we can divide the light year by speed to get time.

9.416 x 10^12
= -------------------
4.000 x 10^5

= 2.354 x 10^7 hours

= 23 540 000 hours

= 980 833 days

= 2 685 years

Good luck,

Paul

Read full answer

Apr 25, 2018 • Homework

0helpful

1answer

Scientific notation on BD - 107i calculator?

Of course it is possible!

There seem to be many ways to do this on this calculator.

Assuming we cannot do scientific notation, we can always do

6.02 x 10 ^ 23 / 3.01 x 10 ^23. However, we have to put brackets in to get BEDMAS to work correctly!

6.02 x 10^23 / (3.01 x 10^23) - for the 10^23, type 10 then the y to the x key and then 23.

Using the scientific notation, we can type in 6.02 EXP 23 / 3.01 EXP 23.

Good luck with your chemistry test tomorrow!

Take care,

Paul

Read full answer

Nov 28, 2016 • Office Equipment & Supplies

0helpful

1answer

Fisher paykel dishdrawer lid will not stay locked

Assuming this is happens with only one drawer - most likely controller is recongising some sensor problems. If the water inlet is faulty then it is waiting for water to get in. Alternatively, the sensor that tells it the drawer is closed suddenly misbehaves and confuses the controller which stops the cycle.

Read full answer

Feb 13, 2014 • Fisher and Paykel 23 in. DD-603SS Built-in...

0helpful

1answer

I HAVE A KENMORE DRYER CALYPSO AND IT ONLY GOES TO 23 MIN. AUTOMATICLY EVERY TIME I TRIED TO UNPLUG IT BUT IT GOES BACK TO 23 MIN. AND DON'T GO OFF UNTIL IT GOES THROUGH THE CYCLE THEN IT GOES BA

could be a faulty sensor or the mechanical programmer. try having a specialized tech look at it.

Read full answer

May 21, 2012 • Kenmore Dryers

0helpful

1answer

Had a power cut today,top draw does not power up

I am assuming you lost power to the house while the dishwasher was running. The power is back but ou are not able to start the top drawer. Is that correct?

Was the top drawer operating at the time the power went off? Are you able to pull the drawer out?
Do any lights turn on when you press the Start button?

Read full answer

Jul 29, 2010 • Fisher and Paykel 23 in. DD-603SS Built-in...

1helpful

1answer

Soap doesn't empty from dispenser

Assuming you are using the correct detergent powder, check if the dishes are remaining dirty.

The water from the impeller may not be rushing up enough due to blockage or limited movement of impeller arm. Follow the insructions to clean the impeller, filter etc or check base of drawer for obstructions to impeller arm.

Read full answer

Dec 04, 2009 • Fisher and Paykel 23 in. DD-603SS Built-in...

0helpful

2answers

Entering 6.02 X 10^23/ 206 =

I think I'm reading this correctly. In your exponent, you are dividing 23 by 206. If so, enter in the calculator the following way:

6.02 x 10 ^(23/206) and then the enter/= key. You should get an answer of 8. The ^ key is 4 keys above the "on" key. You must use parentheses around the fractional exponenet

Read full answer

Aug 07, 2009 • Texas Instruments TI-30XA Calculator

0helpful

1answer

Code C:31:23 quikly flashing over a underlined triangle...HELP!

Error C:31:23 problem means that System Control is not getting Supply Reel pulse. This can be electronic or mechanical problem in camcorder.

Qualified camera tech will fix it properly.

Read full answer

Feb 22, 2009 • Sony Handycam CCD-TRV318 Camcorder

0helpful

1answer

HS-23 problem disconnected

Assuming that the joint which connects the neck strap has been damaged ( see below image )

, I advice you fix the loosed or broken joint back in its proper place permanently by using fevi kwik or some other fast bonding adhesive, but the only problem which will remain is that each time you have to use the headset you will have to wear it through your head andremove it the same way.

Read full answer

Apr 19, 2008 • Nokia HS-23 Headset

Not finding what you are looking for?

View Most Popular

100 Amp 120/240-Volt Transfer Switch #RTSN100A3

Electrical Supplies

23 blinks on the lock light for latitude 2120

Cars & Trucks

97 views

Ask a Question

Usually answered in minutes!

Are you a Generac Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Have a manual for Generac 100 Amp 120/240-Volt Transfer Switch #RTSN100A3? Or just drag it here!

Related Topics:

I assume 23 goes to 23 and 194 goes to 15b is this correct

1 Answer

Randy Parker

1 Related Answer

2Grumpy

Add Your Answer

Attachments: Added items

Related Questions:

23 blinks on the lock light for latitude 2120

Travelinng at 40.ooo kph how long to travel 1 light year

Scientific notation on BD - 107i calculator?

Fisher paykel dishdrawer lid will not stay locked

I HAVE A KENMORE DRYER CALYPSO AND IT ONLY GOES TO 23 MIN. AUTOMATICLY EVERY TIME I TRIED TO UNPLUG IT BUT IT GOES BACK TO 23 MIN. AND DON'T GO OFF UNTIL IT GOES THROUGH THE CYCLE THEN IT GOES BA

Had a power cut today,top draw does not power up

Soap doesn't empty from dispenser

Entering 6.02 X 10^23/ 206 =

Code C:31:23 quikly flashing over a underlined triangle...HELP!

HS-23 problem disconnected

Not finding what you are looking for?

100 Amp 120/240-Volt Transfer Switch #RTSN100A3

23 blinks on the lock light for latitude 2120

Ask a Question

Top Generac Electrical Supplies Experts

vince

Brad Brown

Paul Bade

Are you a Generac Electrical Supply Expert? Answer questions, earn points and help others

Manuals & User Guides

Related Topics:

I assume 23 goes to 23 and 194 goes to 15b is this correct

1 Answer

Randy Parker

1 Related Answer

2Grumpy

Add Your Answer

Attachments: Added items

Related Questions:

23 blinks on the lock light for latitude 2120

Travelinng at 40.ooo kph how long to travel 1 light year

Scientific notation on BD - 107i calculator?

Fisher paykel dishdrawer lid will not stay locked

I HAVE A KENMORE DRYER CALYPSO AND IT ONLY GOES TO 23 MIN. AUTOMATICLY EVERY TIME I TRIED TO UNPLUG IT BUT IT GOES BACK TO 23 MIN. AND DON'T GO OFF UNTIL IT GOES THROUGH THE CYCLE THEN IT GOES BA

Had a power cut today,top draw does not power up

Soap doesn't empty from dispenser

Entering 6.02 X 10^23/ 206 =

Code C:31:23 quikly flashing over a underlined triangle...HELP!

HS-23 problem disconnected

Not finding what you are looking for?

100 Amp 120/240-Volt Transfer Switch #RTSN100A3

23 blinks on the lock light for latitude 2120

Related Topics

Ask a Question

Popular Questions

Generac 43903 standby Generator overspeed indicator on starting

How do i reset overcrank

Generac generator won't turn off in automatic

My generac generator wont start,making a clicking noise and battery is fully charged

I have a generac ix2000 and has an overload light on with no AC power out. what do i need to check?

Top Generac Electrical Supplies Experts

vince

Brad Brown

Paul Bade

Are you a Generac Electrical Supply Expert? Answer questions, earn points and help others

Manuals & User Guides