Does toshiba 27d46 have a reset button? my tv will not turn on and the led light is not on either. checked the power cord & outlets. help!!!

Need to know how many times the led is blinking.

Try this link for more information

Re: tv kdl-55ex620 red light blink 8 times Do a Power Reset. 1. While the TV is off, unplug the power cord of the TV from the electrical outlet. 2. Let the TV remain without power for 60 seconds. 3. Plug the power cord back into the electrical outlet. (If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.) 4. Turn on the TV. 5. When the TV powers on and a picture is displayed, reset the TV to factory default settings.

• If the Reset message does not appear and the TV turns off and on, begin again from step 5.

• If the standby light begins blinking eight times, return to step 1.

6. After the Reset message appears, allow the TV to reset. Do not press any buttons on the remote control or on the TV and do not make any other adjustments for 1 minute. 7. Unplug the power cord from the electrical outlet. 8. Allow the TV to remain without power for 10 seconds. 9. Plug the power cord back into the electrical outlet. 10. Turn on the TV.

• The initial setup screen displays if the above procedures were performed correctly.

11. Follow the on-screen instructions to complete the initial set up. 12. Perform a system software (firmware) update.

Resetting the TV
If the buttons on the remote AND the buttons on the TV case do not work (channels do not change and you cannot open or navigate the menu), the TV has stopped responding. Reset the TV as follows:

NOTE:
Some TVs have a reset button. If available and accessible, try using the reset buttons before using the steps below. Using the reset buttons can save time.


1. Unplug the TV power cord from the power outlet.
2. Unplug any connected devices (DVD, Set-top boxes, etc...)
3. Press and hold the TV power button for five seconds.
4. Plug the TV power cord back into the power outlet and turn on the TV.
5. Open the on-screen menu to confirm that the TV is responding again.
6. Turn off the TV and reconnect the devices.
7. Turn on the TV.

Hope this may help;

Regards,
VOTIT

Here is a manual for that tv. Page 27 says to push the tv/video button but that is on the remote. Do you have a tv/video button on the tv itself? If so, push it until it cycles through to the video input you want

http://www.manualowl.com/m/Toshiba/27D46/Manual/33233

Not sure right off bat, however unplug it from the wall for three or four minutes plug it back in it might reset it?

1. Unplug the power cord from the electrical outlet.
2. Plug another appliance into the electrical outlet to make sure the outlet works.
   • If the electrical outlet does not work , plug the product into another outlet that does work.
   • If the electrical outlet works, but the product still does not turn on , continue to the next step.
   • The power module has a safety feature inside that protects the product during a power surge. If you experienced a recent power surge, the power module might need to be reset. Use the following steps to reset the power module.
     1. Unplug the power supply from the rear of the product.
     2. Unplug the power cord from the electrical outlet, power strip, or surge protector.
     3. If the product uses a power module with a detachable power cord, disconnect the cord from the power module.
     4. Wait 15 seconds.
     5. Reconnect the power cord to the power module.
     6. Plug the power cord back into the electrical outlet. Do not use a power strip or surge protector.
     7. Check to see if the power module has an LED.
        • If the power module does not have an LED, continue to the next step.
        • If the power module has an LED, check to see if the LED lights up.
          • If the LED does not light up, contact HP to replace the power module. To buy a compatible power module, right-click the following link, How to Buy HP , and then click Open in New Window .
          • If the LED lights up, continue to the next step.
     Step two: Test the power on the All-in-One Follow these steps to test the power on the product.
     1. Reconnect the power supply to the rear of the product.
     2. Press and quickly release the Power button ( ) to start a Power On/Off cycle. Do not hold the button down. Figure 1: Press and quickly release the Power button If you press and hold the Power button too long, the product might turn on and then off without restarting. If this happens, press and quickly release the Power button ( ) again.
     • If these steps resolved the issue , there is no need to continue troubleshooting.
     • If the issue persists , see the next step.
     Solution four: Test the power with a compatible power cord from a different product If you have another available power cord that is compatible with your product, use the alternate cord to repeat the steps in Solution three: Reset the power module and test the power .
     • If the product turns on with the alternate power cord, the original power cord caused the issue. Contact HP to replace the power cord. Right-click the following link, How to Buy HP , to buy a compatible power cord.
     • If the product does not turn on with the alternate power cord, continue to the next step.
     Solution five: Service the HP product If you have completed all the steps listed above and are still experiencing a problem, service the product.
     
     
     

May be you can try to perform partial reset by :

1. Disconnect the power cord from the back of the product, and then wait for 20 seconds.
2. Press and hold # and 3 on the product control panel while connecting the power cord to the back of the product.
3. Release the buttons when the product turns on. The reset is complete..

Step one: Reset the power module The power module has a safety feature inside that protects the product during a power surge. If you experienced a recent power surge, the power module might need to be reset. Use the following steps to reset the power module.

1. Unplug the power supply from the rear of the product.
2. Unplug the power cord from the electrical outlet, power strip, or surge protector.
3. If the product uses a power module with a detachable power cord, disconnect the cord from the power module.
4. Wait 15 seconds.
5. Reconnect the power cord to the power module.
6. Plug the power cord back into the electrical outlet. Do not use a power strip or surge protector.
7. Check to see if the power module has an LED.
   • If the power module does not have an LED, continue to the next step.
   • If the power module has an LED, check to see if the LED lights up.
     • If the LED does not light up, contact HP to replace the power module. To buy a compatible power module, right-click the following link, How to Buy HP , and then click Open in New Window .
     • If the LED lights up, continue to the next step.

Step two: Test the power on the All-in-One Follow these steps to test the power on the product.

1. Reconnect the power supply to the rear of the product.
2. Press and quickly release the Power button to start a Power On/Off cycle. Do not hold the button down.

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Hi,
The Standby LED blinks when the TV is turned on, then shuts off when the picture is displayed. If the LED blinks continuously, this may indicate that the TV requires service. Before getting the TV serviced, try power resetting the TV and factory resetting. Try the below steps also: Connect the TV to a different wall outlet and check if it helps. This is to check if the issue is with the Power. Disconnect the TV from the Power Strip or the Surge Protector and connect it directly to the Wall outlet and check if it helps. To Power Reset the TV, disconnect the Power cord for a short period of time (approximately 1 minute). Then, reconnect the Power cord and power ON the TV. To factory reset the TV, turn it ON. Then while holding down the RESET button on the Remote Control, press the Power button on the TV front panel. The TV will turn OFF and then turn ON again. Then release the RESET button to complete the reset procedure. If the issue persists, service may be required.
Good Luck!!

SOLUTION 1 If the HP All-in-One is turned off, press the On button to turn the unit on.

Unplug the power cord from the back of the HP All-in-One.

Wait 15 seconds.

Plug the power cord back into the HP All-in-One.

Turn on the HP All-in-One by pressing the On button.SOLUTION 2: Reset the power module and test the power Step one: Reset the power moduleThe power module has a safety feature inside that protects the product during a power surge. If you experienced a recent power surge, the power module might need to be reset. Use the following steps to reset the power module.

1. Unplug the power supply from the rear of the product.
2. Unplug the power cord from the electrical outlet, power strip, or surge protector.
3. If the product uses a power module with a detachable power cord, disconnect the cord from the power module.
4. Wait 15 seconds.
5. Reconnect the power cord to the power module.
6. Plug the power cord back into the electrical outlet. Do not use a power strip or surge protector.
7. Check to see if the power module has an LED.
   • If the power module does not have an LED, continue to the next step.
   • If the power module has an LED, check to see if the LED lights up.
     • If the LED does not light up, contact HP to replace the power module. To buy a compatible power module, right-click the following link, How to Buy HP , and then click Open in New Window .
     • If the LED lights up, continue to the next step.

Step two: Test the power on the All-in-OneFollow these steps to test the power on the product.

1. Reconnect the power supply to the rear of the product.
2. Press and quickly release the Power button ( ) to start a Power On/Off cycle. Do not hold the button down.

Check for dry capacitors on the tv board

Toshiba flat-screen digital SDTV, 27", won't turn on. Was difficult to turn on for awhile, but some channels had no sound, others that were in English usually, would suddenly turn into Spanish language. A loud static noise would occasionally come on, and then go. TV just won't even turn on now. Is there any possible repair that would be less expensive then replacing the set? I can't lift the set,as it is much too heavy. I'm a senior, and I'm strong, but not that strong.