Does mmats sell the rubber surround for a 12 inch procast? one of my procast needs a new rubber. Do i have to sent it in or can i fix it at home/

Did you burn out the speaker winding or did you break the cone surround? The latter can be fixed for nominal cost and U will have the perfect fix..

If speaker is burnt out it needs to be replaced with a unit that has the same electrical and acoustical characteristics as the original.

The MMATS Pro is going to be too deep for the Pro Box for that vehicle, the only other solution ,may be a custom fiberglass enclosure..

Ebay sell Cerwin Vega Surround (rubber bit) replacements. If he has ripped the cone too, appart from replacing his back legs with wheels (joke!), contact Cerwin Vega directly and they will send you out a new "driver". These are easily fitted at home by any one with a screwdriver

Well i havent had just the rubber problem, I've complete recoils. Contact MMATS. They should do it. http://www.mmatsproaudio.com/ Click contact then email

• Warranty Terms - Parts 1 year limited
• Warranty Terms - Labor 1 year limited
• Product Height 12"
• Product Width 12"
• Product Weight 7.8 lbs.
• Product Depth 6-1/2"
• Subwoofer Size 12"
• Resistance (Ohms) 4 ohms
• Bottom Mount Depth (inches) 10"
• Woofer Composition Mica-reinforced woven glass fiber composite
• Woofer Surround Rubber
• Peak Power handling 1300W
• RMS Power Range (Watts) 380
• Cutout Diameter or Length (inches) 12"
• Sensitivity 84dB
• Frequency Response 30Hz - 1kHz
• found at:::---- http://www.bestbuy.com/site/Sony+-+Xplod+12%22+Single-Voice-Coil+4-Ohm+Subwoofer/9202481.p?id=1218057724056&skuId=9202481
  

http://www.mmatsproaudio.com/subwoofers.html
click specs

Hi there,

you need to reseal the speaker in the box, its loosing the compressed air inside.

Hope this helps

alex

Contact MMats Pro Audio at 561-842-0600. They can re-cone it for you, or sell you the re-cone kit. If that does not work for you, contact MWA Speaker Parts in Tuscon - 520-647-7193. They can sell you a re-cone kit, or they can direct you to a speaker repair center near you. A third option would be to contact Sundown Audio in Troutman, NC. They may be able to re-cone it for you.

what model speaker. i recommend matching your MMATS speaker with a MMATS amp. Match the RMS

First, the specs:

• PPI 4200am = 50x4 at 4 ohms, 100x4 at 2 ohms
  
• Alpine 3553 = 35x4 at 4 ohms, 50x4 at 2 ohms
  
• Mmats D500.2 = 350x1 at 4 ohms, 500x1 at 2 ohms

• 3x Mmats Procast 12 = Dual 4 ohm VC
• 1x JL 15w6 = Dual 6 ohm VC
• 2x JL 15w0 = Single 8 ohm VC
  

Second, I don't think I would recommend mixing n' matching the subs. One of the subs would always be working harder than the rest. If you want to run multiple subs, make them all the same. Sometimes, you can get away with it if they are all the same voice coil impedance, but in this case you've got dual 4 ohm, dual 6 ohm, and single 8 ohm subs all in the mix.

If it were me, I'd probably stay with the single 15w6. But it's your money :)