Question about Nordic Track NordicTrack Treadmill, A2550

2 Answers

Nordic Track A2250 Pro stuck inclined

My Nordic Track A2250 Pro is stuck in the incline position. There was a knocking noise coming from the rear left (when on the machine) corner. I tried to fix this by recalibrating the incline. I followed the instructions in the manual, but the machine never declined. I've tried recalibrating many times, but it never attempts to move. Now it won't even move the belt. Any ideas?

Posted by on

  • diverdiva1_p
    diverdiva1_p Mar 19, 2013

    I know this is an old post , but this is exactly what is happening to me. What the repair costly or easy fix?

  • Anonymous Apr 01, 2014

    Nordic rack elite 5700 noise when incline or delince

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

My Nordic Track Treadmill A2250 is stuck on the 12% incline position and it wont go back down and I have tried to reset it by turning it off, switching the reset button to off and then on or even unplugging it several times. What would be my next move?

Posted on Feb 13, 2011

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

Buckmanservices.com an online Fitness Diagnosis company.. they have 24/7 techs ready to save you money they only charged me $30 they saved me hundreds..I recommend them for sure

Posted on Jun 13, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Nordictrack treadmill model T7si is stuck on the 10 incline position. How do I fix it?


Check that the incline plus switch is not jammed or likely there is a defect in the panel circuit causing plus incline to be repeated. This needs to be trouble-shooted by removing and testing the panel circuit.

Oct 07, 2014 | Nordic Track Exercise & Fitness

1 Answer

Nordic track reprogram card


have the card checked.. see if its going bad..

Jan 08, 2014 | Exercise & Fitness

1 Answer

C2250 treadmill incline recalibration - incline goes up, not down


Plug the power out and plug it back in after a count of 50 could be that it needs to be reset .then plug back in the power and see what its doing if no luck go to manual and look for reset

Jan 06, 2014 | Nordic Track Exercise & Fitness

1 Answer

Nordictrac a2250 beeps when key is attached


adjust the reed switch first, and after RUN the software calibration for diagnose and troubleshooting. see the diagram

God bless you
6_20_2012_12_48_33_pm.gif6_20_2012_12_48_46_pm.gif

Jun 17, 2012 | Nordic Track NordicTrack Treadmill, A2550

1 Answer

Incline goes up and down


I had the SAME problem, several time, with my NordicTrack A2250 Treadmill.
Allow it to go fully up and then fully down several times, without turning it off. IT seems to "cycle" that way 3 times and then "reboots" itself and starts working normally, again.
I had to figure this out myself... none of the suggestions I read worked.

Apr 24, 2010 | Nordic Track NordicTrack Treadmill, A2550

1 Answer

I have a Nordic Track EXP1000i Treadmill. The


I know it's been months, but, if you still have this problem try this: 1. remove the philips screws holding the motor/belt/electronics cover on: you can lay the whole thing on it's side and remove them from the bottom. there's two in the front and two on the sides.
2. Obviously, unplug the unit! before doing anything. lay the unit back on it's feet (normal position)
3. Find the incline motor assembly. it will be int he middle of everything. black tube thingy.
4. take a cordless drill with a flat head screw driver bit, and turn the incline motor CCW. until the bed is flat.
5. what what I have read, you should shop for a new incline sensor. these fail before the motor does.

Oct 22, 2009 | Nordic Track Exercise & Fitness

1 Answer

Incline stuck- keep going up and dopwn. Treadmill


I had the SAME problem, several times, with my NordicTrack A2250 Treadmill.
Allow it to go fully up and then fully down several times, without turning it off. IT seems to "cycle" that way 3 times and then "reboots" itself and starts working normally, again.
I had to figure this out myself... none of the suggestions I read worked.

Oct 05, 2009 | Nordic Track NordicTrack Treadmill, A2550

Not finding what you are looking for?
Nordic Track NordicTrack Treadmill, A2550 Logo

2,053 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nordic Track Exercise & Fitness Experts

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

135 Answers

Treadmill Repairs...
Treadmill Repairs...

Level 2 Expert

338 Answers

Android Man
Android Man

Level 2 Expert

278 Answers

Are you a Nordic Track Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...