Need info on putting line on troy bilt 4-cycle string trimmer. Need to know how to get spool off trimmer to replace trimming string on the spool.

Contact the consumer desk.

TB22 EC Curved Shaft String Trimmer by Troy-Bilt

www.troybilt.com/.../troybilt/TB22EC-trimmer

Troy?Bilt Products
Rating: 3.7 - ‎232 votes - ‎$99.99 - ‎In stock
25cc, 2-Cycle Gas Trimmer / Attachment-Capable Design ... The TB22 EC gas string trimmer is both JumpStart™ and TrimmerPlus® attachment capable, making ...

Gas Trimmer ' TB635 4-Cycle Curved Shaft ... - Troy-Bilt

www.troybilt.com/.../troybilt/tb35-ec-curve-shaft-gas-...

Troy?Bilt Products
Rating: 3.3 - ‎32 votes - ‎$179.99 - ‎In stock
The TB635 EC curved shaft gas trimmer with SpringAssist™ technology features the new Click N Trim™ bump head, making line replacement easier than ever. ..... next one they put on - will only run for about 4 seconds. they've had for about 2 ... Both String Trimmer and Edger work great, easy to start and very low vibration.

how do you put string on troy bilt 4 cycle curved shaft TB20CS

Try mixing up some fresh gas mixture if it is over 30 days old it is considered bad gas. Or the carburetor may need to be rebuilt.

If you have the starter spool out (the one the rope goes in)...Here is what to do. Take the starter spool and change the rope out putting it back exactly as it was. Leave the rope hanging. Hold the spool and set it down on the rewind spring. Turn the spool on the rewind spring until you feel it is tight enough. While turning, hold the rope in the little slot in the spool so it can go around without hanging up. Once it is tight, get the rope in line with the spool opening and SLOWLY let the rope rewind. Put on the handle and put the unit back together.Good luck...Lee

far enough so that you can reach through filler cap and pull the line out to attatch fuel filter.
then you can pull it back in and let it rest on the bottom of the tank

On the bump mechanism, line up the two arrows, then unscrew the bump, this will release the spool, then you wind the two strings in the opposite directions, the arrow on the spool will tell you the direction to wind the string, replace spool, spring, bump feed, and you are good to go. I hope this has helped you.

If it's like my Ryobi, the alignment arrows are for feeding in string, not removing the spool. When aligned with the arrows, you should be able to insert two pieces of line into opposite sides of the housing. The ends of the line will come out of the spool next to a tiny hole. Put the end of each of the two lines into the holes, then pull the two lines from the outside. This will lock the ends of the line into the tiny holes in the housing. Now you can turn the housing by hand to wind the lines onto the spool. I think it will take about ten feet of line (on each side).

Alternatively, spin the bump stop out of the assembly. This holds the spool in, so when the bump stop is removed, the spool comes right out.

I hope this helps.

Cut two separate pieces of string, about 7 ft. each.

Stick the end of the line in the hole on the inside of spool.

Wind clockwise onto spool, putting the line that is closest to the ground on first.

Once you have winded this piece on, lock the last 4 inches of line through the slits on spool.

Repeat process for second piece of line, locking the last 4 inches in slot opposite the other locked in piece.

Put the spool on the trimmer, feeding the end of lines through either hole on trimmer.

Before you push the spool all the way on, pull the strings out of the locked position.

Jim

Cut two separate pieces of string, about 7 ft. each.

Stick the end of the line in the hole on the inside of spool.

Wind clockwise onto spool, putting the line that is closest to the ground on first.

Once you have winded this piece on, lock the last 4 inches of line through the slits on spool.

Repeat process for second piece of line, locking the last 4 inches in slot opposite the other locked in piece.

Put the spool on the trimmer, feeding the end of lines through either hole on trimmer.

Before you push the spool all the way on, pull the strings out of the locked position. Put cap on and GO CRAZY!

Jim

I just had this same issue. I found out that you have to take the cord out of the handle then put the spool in. You then rotate the spool back in and align the spool with the spring and fish out the cord which will put a small amout of tension on it. You keep the tension on it and put the handle back on.

Rgds,
Mark J