Error code: 0xd0620230

Solution 1: Replace the Waste Ink Absorber
Step 1: Press the Power Button
* With the Canon Printer Powered off but connected to a power source. Press the "Power" button while pressing and holding the "stop/reset" button.
Step 2: Press the Stop/Reset Button
*When the Power is lit, press the "Stop/Reset" button two times
*While pressing and holding the "Power" button
Step 3: Move Into a Service Mode
*When releasing the "Power" button and the "Stop/Reset" button (regardless of order), the printer will move into a service mode. (waiting for menu selection)
Step 4: Press "Stop/Reset" Button
*When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the function listed in the table below.
(Each time the "stop/reset" button is pressed, the LED lights alternately in orange and green, starting with orange)
Note: Make sure there is need to press 4 times for waste ink counter reset
The number of the Reset button pressing LED Function Remarks
*0 time Green Power off
*1 time Orange Service pattern print
*2 times Green EEPROM print
*3 times Orange EEPROM reset
*4 times Green Waste Ink counter reset

Step 5: Turn on Canon Printer
Turn off the printer, then turn it on again.

Now Check the Canon printer error code 5800 is resolved. If not, then go to the next solution.

Solution 2: Enter Canon Printer in Service Mode, works best for multifunctional printers.

Step 1: Turn Off Canon Printer
Step 2: Go to Press the Menu Option
Step 3: Put Printer in Service Mode
*To do this you will have to press the "SCAN", "COPY" and "SCAN" buttons in that exact order.
Step 4: Reach to the "Counter Access" option
Step 5: Check amount of pages that you are printed
Press the "ok" key
Step 6: Press the "COPY" Button
Step 7: Score all the way to zero
Step 8: Stop once get "Scan Page Count" Option
Step 9: Set Score back to zero
Step 10: Press the "STOP/Reset" button
Step 11: Turn Off "Stop/Reset" button
Step 12: Disconnect the Power Cables and reconnect

hi, change printer's head carriage assembly.

1. plug off power cable
2. press and hold stop/reset button
3. plug on power cable
4. press and hold power button(still hold stop/reset buttn)
5. still hod power button, loose stop/reset button
6. press stop/reset 2X then loose power button, wait until 0 displayed
7. press stop/reset 1X
8. press power button 1X, printer will print 1 time
9. press stop/reset 2X
10. press power button 1X,printer will print 1 time
11. press stop/reset button 3X
12. press power button 1X ( no print proses)
13. press stop/reset 4X
14. press power button longer than before for turn off printer, if print not turn off plug off power cable
15. turn on printer and error 27 will disappear

i hope this helpfull
thanks for using fixya

I managed to track down some information that may be able to help you. Power off your printer, then press &hold buttons while powering on. If it doesnt reset then unplug it & press & hold buttons while plugging it in.
# & 3 Partial reset
# & 6 Semi full reset
# & 9 Full reset
A full reset will clear any stored information in th printer, speed dials ect. So always start with a partial reset and work your way up.
I hope this helps.

Error 2200 is a scanner stall error.. there are a couple things for you to try to fix it:

Power off the AIO and remove the power supply(Power Cord) from the back of the unit.
Open the scanner cover. Check the scanner glass for cracks and the scanner casing for cracks. Close the scanner lid.
Open the top cover of the AIO.
Using the carrier belt, move the cartridge carrier to the middle of the unit.
Remove both cartridges, close the top cover, reinsert the power supply, and power the AIO on.
IF THE ERROR MESSAGE DID NOT COME BACK....
Power off the AIO and remove the power supply from the back of the unit.
Open the top cover of the AIO.
Using the carrier belt, move the cartridge carrier to the middle of the unit.
INSERT THE COLOR CARTRIDGE ONLY,
Close the top cover, reinsert the power supply, and power on the AIO.
IF THE ERROR MESSAGE RETURNS.. GET A DIFFERENT COLOR CARTRIDGE AND REPEAT THIS PROCESS....
IF THE ERROR MESSAGE IS GONE,
Power down as before, do all the same to get the carrier to the middle of the unit and RE-INSTALL THE BLACK CARTRIDGE.
Power back up as in previous steps...
NO ERROR? SHOULD BE GOOD TO GO..
ERROR?? TRY DIFFERENT BLACK
If after trying all of the above and the error message does not go away, you unit would need serviced (if it's under warranty, it's worth it; if not, you might want to replace it.)

IssueAn 0xc18xxxxx or 0xc19xxxxx ink system error code displays on the front panel. The printer cannot copy, receive faxes, or print. Solution
Press the On button to turn the printer off. 
Unplug the power cord from the back of the printer.
Remove all the ink cartridges.
Wait two minutes.
Plug the power cord into the back of the printer.
Press the On button to turn the printer on. 
Install the ink cartridges when prompted.
If the error code does not display, the issue is resolved.
If the 0xc18xxxxx or 0xc19xxxxx ink system error code displays on the front panel, service the printer.

My mother's printer had a similar problem, I was able to find this solution on the HP site.

Disconnect the USB cable from the back of the printer, but leave the printer turned on.

Open the cover of the printer and remove the print cartridges.

Close the cover and wait for the Insert Ink Cartridges message to display.

Disconnect the power cord from the back of the printer and wait for one minute.

Reconnect the power cord. If the printer does not automatically turn on, press the Power button.

Open the cover and reinsert the print cartridges.

Close the cover. If prompted, print a calibration page.

Reconnect the USB cable, and try to print a print job from the computer.

I hope this helps you too...

Hi,

It might be a hardware issue however u can try the following basic troubleshooting steps .

Unplug the power cord from the back of the unit . try to move teh carriage manually .

perform a reset as well .

1
Take out the cartridges from the unit .
2
Make sure the unit is connected to the wall jack directly without any surge protector.
3
Unplug the power cord from the back of the unit ( without turning off the unit ) .
4
Now press the # and 6 key together , while holding these keys down plug in the power cord back into the unit .
5
Do not release the keys after a few seconds u will find te hp logo or bars moving across the screen .wait while the unit turns off.
6
after one minute turn on the prnter . it will go into alligment phase > let it finish .
7
after its done > try to make a copy .

Note - you can also try the Ok n cancel key combination in place of # and 6

Thanks

Issue An 0xc18xxxxx or 0xc19xxxxx ink system error code displays on the front panel. The printer cannot copy, receive faxes, or print. Solution

1. Press the On button to turn the printer off.
2. Unplug the power cord from the back of the printer.
3. Remove all the ink cartridges.
4. Wait two minutes.
5. Plug the power cord into the back of the printer.
6. Press the On button to turn the printer on.
7. Install the ink cartridges when prompted.

If the error code does not display, the issue is resolved. If the 0xc18xxxxx or 0xc19xxxxx ink system error code displays on the front panel, service the printer.     Here is a manual if you dont already have one.   http://h10032.www1.hp.com/ctg/Manual/c00486336.pdf

Fiend your solution direct from hp. Here is your solution...


http://www.hp.com/printer/prob676ijt65/solution
732