I have a casio CE-3700, I do not have the instruction manual. I do keep getting error code 01 after I did the clear out

Hi Josie. E33 means you have not entered amount tendered.

turn key to REG
Press SUBTOTAL
An amount should show on the display. Note this amount.
Type the amount shown on the display with no decimal e.g if display shows 12.30, type 1230.
Press CASH
Drawer should open.

If you cannot clear the error (try the clear button C) or no amount shows when you press SUBTOTAL, it probably means the memory has become corrupted due to a flat or faulty battery.

--------------------

If anyone needs more information, C-tech collective have the Casio CE-3700 manuals here:

http://the-checkout-tech.com/manuals/cashregisters/Casio1.php

What were you doing or trying to do when you got this error code?

Which percentages? Which reading? You will need to be more specific. If it is part of the daily report, the user manual should be able to show you what they mean. If you need more information, the Casio CE-3700 manuals are here:
CE-3700 Operation/ programming manual:
http://the-checkout-tech.com/manuals/cashregisters/Casio_CE-3700_operators_and_programming_manual.html
CE-3700 Service (repair) manual: http://the-checkout-tech.com/manuals/cashregisters/Casio_CE-3700_and_CE-3750_service_manual.html

If you have performed a RAM (MAC) clear, then the departments should work as soon as the MAC code has been set. Make sure you aren't using a decimal point for prices. -----------------------------------------------------------
If anyone needs more information,
The Casio CE-3700 User and Programming manual is here: http://the-checkout-tech.com/manuals/cashregisters/Casio_CE-3700_operators_and_programming_manual.html
The Casio CE-3700 Service (repair) manual is here: http://the-checkout-tech.com/manuals/cashregisters/Casio_CE-3700_and_CE-3750_service_manual.html

It sounds like there is a good reason for it locking up the first time then. Most commonly it is caused by a printer problem. Most Casio models will run the printer before they turn the display on, so if you can't hear the printer run at turn on, I'd start there. Look for paper jams. make sure the motor can turn freely. If the motor is okay, check the battery. You can experience weird problems if the battery has not been replaced on time. ------------------------------------------------------------------------------------
If anyone needs more information, the manuals are here:
Casio CE-3700 Service (repair) manual: http://the-checkout-tech.com/manuals/TOC/cashregisters/Casio/CE-3700%20and%20CE-3750%20service.TOC.pdf
Casio CE-3700 User and programming manual: http://the-checkout-tech.com/manuals/TOC/cashregisters/Casio/CE-3700%20operators%20and%20programming.TOC.pdf

You have logged yourself off. Try pressing 1 then CLK#
------------------------------------------------------------------------------------
If anyone needs a Casio CE-3700 manual, C-tech has them here: http://the-checkout-tech.com/manuals/cashregisters/casio1.php

This is caused by incomplete initialisation. it means the program may be corrupt from being unplugged for too long, or you may have a bad battery inside the machine (change it every five years).
Firstly, try a flag clear to jump it back to REG mode:
Turn power off at wall Turn key to program position Hold down RECEIPT FEED button. Keep your finger on it. Turn power on at wall Wait 5 seconds, then let go of RECEIPT FEED Press SUBTOTAL
Turn key back to REG mode and try it. If the programming is corrupt, you will often see the decimal point in the wrong place.
If you want to re-program it, there is a manual for the CE-3700 here:
http://the-checkout-tech.com/manuals/TOC/cashregisters/Casio/CE-3700%20operators%20and%20programming.TOC.pdf

http://www.fixya.com/support/t1831298-in_usa_casio_ce_3700_e04_message

Hi. It means the password has not been entered. I suspect this machine has not been RAM cleared properly after the battery was changed. What MAC code did you enter when you changed the battery and initialised it?

Mark

Hi. I would advise both of you to try a flag clear first to see if you have any program left.

Turn key to program. Power off at wall.
Hold RECEIPT FEED, and turn power on at wall.
Wait 10 seconds, then let go of RECEIPT FEED.
When you see 'FFFFFFFFF' press SUBTOTAL.
Turn key back to REG and try it.

If you still need help, let me know.

Mark