1st trk cuts off when i try to rec the 3rd trk

Mute Switch/Mute-Clip LED :

• This switch mutes all Aux, Group and L/R sends from the corresponding channel.
• This switch is equipped with a red LED that will illuminate when the channel is muted.
• When the MUTE button is out,the LED functions as a Clip indicator that will illuminate at 2 dB below clipping.
• Muting the channel does not prevent the PFL signal from being sent to the PFL/AFL mix when the PFL Switch (12) is in.
• This switch mutes its respective Group send from the Group channel.

Go to page 11 in this link :
Peavey FX Mixer Series Operating Manual

You can also try, Restoring Factory Settings, in the Utility Menu Options.
Go to page 16 in ths link :
Peavey FX Mixer Series Operating Manual

CAUTION:
Restoring the factory settings option resets your mixer's presets, reformatting factory presets and erasing all other user presets. (This option is handy when your venue has permanently changed and all-new presets are required.)
Once confirmed, the presets are not retrievable and will be permanently lost.
Should you select this option in error, a warning screen allows you to cancel the procedure.

First, check your levels on the console. Is anything turned up high, channels, gain settings on channels? Check and see if the noise exists whith the main outputs muted or turned down. If it goes away it is a fader or gain setting on a channel. If it persists, then you have a co nection issue with the USB . Try a different cable. Make sure the Mac is on the same electrical circuit as the mixer, or if it is on battery, try adding it on the electrical circuit with the mixer. See if location of the mixer to the computer makes a difference as well. They may be too close to each other. Hopefully one of these things will fixya.

The "rude solo" wil only flash if something is soloed. You need to check again as there is STILL something soloed. The left meter is because that is showing the channel that is being soloed. Once you unsolo everything, the meters wil display full left and right as usual.

From page 84 of your user manual, the signal flow diagram shows that the two effects busses can be sent to the sub busses. You CANNOT send the subs through the effects unit since that would loop... so the effects that are selected from the channels onto the two FX busses which are then processed into the effects signals, then can be ADDED into the sub group signals. Make sure the subs are NOT selected to the mains and the solo of the subs is not set Nor is the sub mutes. You say the subs are showing signal... MAKE SURE THIS IS with the indicators set to display "Output" as that is the one that counts.. If the output when the sub is selected shows no signal, then likely the mute for the sub has gotten set.

Make sure you start and terminate the sampling on the beat... otherwise when looped the thing can't "splice" the sample without clipping the sample to tie the start and finish together... and keep the rhythm.

You might want to review your manual regarding modes they may have that are more tolerant of the splicing of the sample.

Understanding the problem is half the solution!

It is intended to do automix on the "solo group". The auto mix apparently levels mics that are receiving audio and reduces or mutes those not receiving vocal activity for each of the groups. The mixer has abiliity to select certain channels into the three subgroups, one of which is the "solo".

press knob 1 and 2 and rec at the same time , then power on , then knob bank D , power off and on ,,,,, ready
Greetings Gerrie ( Holland )

Try posting this under Motors. It has been accidentally posted under Musical instruments.

I believe the keyboard wants COMPRESSED type filles such as MP2 or MP3. Try those.

Korg Pa800 Synthesizer i have noise on ram samples Answer i turned on my pa800 and when i play ram samples there was some noise like cracking and distortion,... (More) i turned on my pa800 and when i play ram samples there was some noise like cracking and distortion, that happened 2 or 3 times, now its normal, but i think it may hapen again??? where is the problem, somebody says it is on motherboard? or its just ram overheating? since i install 2.01 os i noticed that its kinda warm in right display corner, can u help me???