Stops, several bleeps then shows "LE" in display, & shuts down, even if machine is VERY lightly loaded. Sometimes works OK with bigger load, sometimes goes part way through, other times, stops during initial filling, sometimes goes right through until final spin. Does not seem to be load related - now. Will repower up after mains removed but sometimes fault shows, other times goes right through with no further problem. Machine is 4 years old but not had heavy useage (once or twice per week).
I have a wm-1480fhd doing the same. It stops full of water on final rinse, shows 'LE' in display and beeps. Switch it off and on, do a rinse program and it will finish the cycle. I have found that if I make sure the house hot water tank is hot and feeds the machine with hot water then the washing machine works perfectly. Anybody have any ideas which bit is broken?I have a wm-1480fhd doing the same. It stops full of water on final rinse, shows 'LE' in display and beeps. Switch it off and on, do a rinse program and it will finish the cycle. I have found that if I make sure the house hot water tank is hot and feeds the machine with hot water then the washing machine works perfectly. Anybody have any ideas which bit is broken?
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Daewoo Washing Machine Error Fault Code = LE Fault Detected: Washing Machine Door Open Washer Has Detected: Washing machine detected door as open or not locked Check / Repair / Fix = Close door – Door lock switch – Door latch – PCB
LE error in your LG front load washer is displayed
when either the motor is not working or the control board thinks that the motor
is locked up. A Hall Effect sensor is used in these washers which monitors the
speed and direction of the motor and then forwards this information to the
control board. Hope you understand by now that this LE error is displayed when there
is an issue with the motor or when the Hall Effect sensor sends wrong signal to
the control. Conclusion is you'll have to check both motor and hall sensor and
replace the part# that is bad, usually I have seen the sensor going bad. Please
get back to me if you have any other questions.
zanussi zwf1650w washing machine. when starting any program after a few seconds machines stops and shows draining 0.0. have done diagnosis test and shows fault E91 & E48 fault codes also shows E34 code. any help much appreciated.
No, this is not the same as the LE code. The FE code indicates an overflow error or condition. The things to check out would be the drain and the drain line to make sure there are no kinks in it. The drain hose can get clogged with sludge and sometimes a hot wash with a 1/2 cup of vinegar will clean out the sludge. If that doesn't work, I would take a look at the pump to make sure it is not clogged with anything and that the pump impellers are good. Take a flashlight and look into the suction port of the pump. Look for any broken or missing impeller blades. If any are broken or missing or if the impeller will not move freely, the pump would need to be replaced. Hope this helped and best wishes.
Lets go. say the coed was 1234,Press button number 1 untill you got number one on your display.Then press number 2 until it shows on the display .Then press number three untill it shows on the display and the same for number 4.Hold down the last button until you here a bleep then you should be ok.
had to call an enginer out, the problem was down to a faulty motor rota, to identify if e30 is this fault, rotate the drum (so the motor rotates) and try to start the m/c. if it runs ok you know to change the rota. hope this may help someone
Machine has a bad motor or "stator" on this machine. It is a direct drive winding on the back of the machine. Remove the back panel, the one bolt removes the rotor then you will see the stator winding, replace it and your good to go.
I have a wm-1480fhd doing the same. It stops full of water on final rinse, shows 'LE' in display and beeps. Switch it off and on, do a rinse program and it will finish the cycle. I have found that if I make sure the house hot water tank is hot and feeds the machine with hot water then the washing machine works perfectly. Anybody have any ideas which bit is broken?
×