Is the display intended to be illuminated or is it to be read 'in the dark' so to speak? As it is digital, and as the model in the store appeared to be illuminated, I don't understand why I cannot view the display without a flashlight. Thank you - ez [email protected]

Question edited to add SPACES.
Question edited to English.

In a website where everyone speaks English, you appear to writing in German. We are a North American website, we only speak English here.

https://translate.google.ca/

Replace the capacitor on the back of the display board.

..

[PDF]USER MANUAL - Newegg.com

images10.newegg.com/User-Manual/User_Manual_89-262-370.pdf

To get the most out of your new VIZIO product, read these ... Follow all instructions. ...the provided plug does not fit into your outlet, consult an ... Doing so could short circuit parts causing a fire ... the screen of the coaxial cable is intended to be connected to...... setting is too high, the picture may appear faded or washed out.

GPCT Multi Function Digital Talking Projection Alarm Clock ...

www.amazon.com/GPCT...Digital.../dp/B00IDZ6V4I

Amazon.com, Inc.With a talking function, your alarm will report the current time in English so ... TimeSet, Dual Alarm, Sleep Timer, Indoor Temperature/Day/Date Display .... u pick theclock and look at the clock very near to see the faded LCD Display. ... but I wanted aclock that put the time on the ceiling all the time, not just when prodded.

[PDF]USER MANUAL - Vizio

www.vizio.com/documents/downloads/hdtv/.../UM_P602uiB3.pdf

VizioTo get the most out of your new VIZIO product, read these instructions before ... the provided plug does not fit into your outlet, consult an ... Doing so could short circuit parts causing a fire .... the screen of the coaxial cable is intended to be connected to.... Setting the Sleep Timer . ..... HDMI is the intelligent, all-digital interface.

No air conditioning and blank thermostat display

www.handyguyspodcast.com/.../no-display-on-the-thermostat-and-no-ac...

Read your manual about a contrast control for the display. At one end of the range of control the display is almost invisible. Sometimes there is a little shaft/knob on the back, other times it is a menu item and yes, it is hard to see the display to adjust the display... just go through the procedure blindly to see if it comes back. Also illuminate the display if dark with a flashlight and see if there are display characters there but just lacking a backlight. A backlight failure could be the problem.

F30, indicate an electronic communication problem with the washer. Some Duet models are equipped with electronic displays that will read "F30" when this error occurs. Models without displays instead illuminate a given combination of LEDs to indicate an error. In the Duet Sport, for example, when the "Wash," "Rinse," "Spin" and "Cycle Complete" LEDs are are illuminated at the same time, an F30 error is present.

Other comments about this problem suggest "storing" detergents on the top cover. A new, full bottle of Tide caused problems for us. Cleared the top of it, problem solved.

I suggest visit and check this link: Use and Care Guide

Hope helps.

Not sure on the make but it appears that the timer clock display is failing. Replacement cost is typically £80 but without the make i cannot give you a accurate costing. Fitting would be extra.

Regards
Aardvark Repairs

press the mode button until the display reads "off". Remove the four screws holding the control cover on. Swing panel down so that the back of the board is visible. Press the mode button until "RESfl" appear. Press and hold both "up" and "down" buttons for 5-7 seconds until three dashes appear (---). This resets the fault history and clears any stored faults.

just change the setting to outdoor. if you read your manual it will explain how. pg 27

The digital sensitive lens has worn out... that part needs replacement... If you know where to buy or a repair center can solve it, if they have that part....

Good luck.. happy Fixya

***Storing a Number for Speed Dialing*** 1 Press Phone Book on the control panel. 2 Press Phone Book or the scroll button (􀂥 or 􀂊) to display ?Store&Edit? on the bottom line of the display. Press Enter. 3 Press Enter when ?Speed Dials? appears on the display. The display prompts you to enter a location number, showing the first available number. 4 Enter a one or two-digit speed dial number between 0 and 79, using the number keypad or scroll button (􀂥 or 􀂊), and press Enter. If a number is already stored in the location you chose, the display shows the number to allow you to change it. To start over with another speed-dial number, press Upper Level. 5 Enter the number you want to store using the number keypad and press Enter. To insert a pause between numbers, press Redial/Pause. A ?-? appears on the display. 6 To assign a name to the number, enter the name you want. For details about entering characters, see page 1.14. If you do not want to assign a name, skip this step. 7 Press Enter when the name appears correctly or without entering a name. 8 To store more fax numbers, repeat steps 4 through 7. To return to Standby mode, press Stop/Clear. ***Sending a Fax using a Speed Number**** 1 Feed the document(s) face up into the ADF. For details about loading a document, see page 2.2. 2 Adjust the document resolution to suit your fax needs. See page 2.3. If you need to change the darkness, see page 1.20. 3 Enter the speed dial number. ? For a one-digit speed dial number, press and hold the appropriate digit button. ? For a two-digit speed dial number, press the first digit button and hold the last digit button. The corresponding entry?s name briefly displays. 4 The document scans into the memory. The fax number stored in the speed dial location is automatically dialed. The document is sent when the remote fax machine answers

Recording a subject that is outside the flash range can cause the subject to appear dark in the resulting image, because not enough of the flash reaches the subject. When this happens, you can use flash assist to correct the brightness of the recorded subject, so it appears as if the flash illumination was sufficient. Note, however, that recording certain types of subjects may not produce the results you expect, even if you use flash assist.