Hi there! How do you do a conference call on this phone? thanks! Christina

To make conference call, call a number wait until answer if answer dial again another number do not end all active calls just hold and dial again as long as five numbers then, go to option select conference.

Hi,

This is how to make conference call. Dial the first number on your phone, when the person pick the call, put him/her on hold by pressing the option button and scroll down to hold.

Dial the the second number, when the person pick the call, press the option button and scroll to conference call. Select it and start making conference call.

Regards

Hello

i have the same problem, do you know how to solve it ?

Thanks

Hi,

its simple just call a number, while calling the number try dial another number once the other person picks the call click options you will see conference call.

thanks.

PLease do below listed Steps 1. make call 2. Put first call on Hold and make 2nd call 3. Open Option button and select Conference from menu Note: you need to active conference service from your service provider and also your phone has to supported conference service.. Thanks

Hi,

Try following this conversation with H.P;

Christina: Let us perform some steps to isolate the issue and find a fix for it.
Christina: Please perform the following steps and let me know the message that will be displayed on the printer.
Christina: A. - Press and hold the “*” key.
B. - Press the “#” key and release both keys.
Display should say “Enter Special Key Combo”
C. - Press and release in sequence the “1”, “2” and “3” buttons.
CustomerName: ok
CustomerName: screen says "support" R0631M
Christina: Fine.
Christina: 2. Press and release the right arrow button until the display says “System Configuration Menu”.
Christina: 3. Press and release the “OK” button.
Christina: 4. Display should say “Hardware failure status”. If not there already, Arrow Key over to “Hardware failure status”,
Christina: 5. Press and release the “OK” button.
Christina: 6. Display should say “Hardware failure status: Clear. Press OK to clear”.
CustomerName: yup
Christina: 7. Press and release the “OK” Button. Message changes to “Hardware failure status Cleared. Press Cancel to continue”.
CustomerName: ok
Christina: 8. Press and release the “CANCEL” button as many times as necessary, so that, either the “Welcome to Photosmart Express” screen appears, or, the “Ink System Failure” screen appears. PLEASE DO NOT TRY TO PRINT AT THIS STAGE.
CustomerName: ok
Christina: 9. Using the Power Button, turn the unit OFF and unplug the power cable from back of the printer and wall outlet.
CustomerName: done
Christina: Fine.
Christina: 10. Wait 30 seconds for the power to get discharged and then plug the power cable into the wall outlet first and then into the back of the printer
CustomerName: done
Christina: 11. Turn the unit on. The printer may display message “USE POWER BUTTON TO SHUTDOWN THE PRINTER” followed by “PRESS OK TO CONTINUE”. Press OK. The Printer will start the “ONE TIME INK INITIALIZATION PROCESS”. Allow this process to complete and do not interrupt. Once the initialization process is complete, the printer will print out a Diagnostic Page.
CustomerName: made a buncha noise, and it didn't print a diagnostic page
Christina: Good.
Christina: Is the error message still being displayed on the printer?
CustomerName: nope
Christina: Good.
CustomerName: should I try to print something?
Christina: Let us print a self test page to check the functionality of the printer.
Christina: Press Setup menu on the All-in-One then scroll using the arrow key and select Print Report then select Self Test Report.
Thanks

Fame !

dont have yet

this will be threw your service provider to set up more than a 3 way calling plan
3 way should be standard service with only 3 people at time anything extra needed the service provider can set up the extra 3 waying +

on the phone handset if your just looking for in home conference calling to others just click the conference button find the handset you want to talk too or all the handsets this is conference calling

No most system are maxed on the phone ... but if you had a panasonic system they are know for multi conferencing.

Here are some steps that should help. I don't think that you can Conference call You can hold a 3-way conversation (conference call) between your handset, an external caller and another internal handset user. During an external call: 1 Press . The external caller is put ?on-hold?. 2 Press or to select name, number or the handset you want to have a conference call with and press or key. The called handset will ring. 3 When the called handset answers, press to start your conference call. 4 Any handset can press at any time to leave the conference call. It looks like you can use the multiple system sets together, but the system is not designed to do what you are asking for. Please repost with any other comments or questions. Please rate this solution through fix-it. Thank you.