Install wireless mouse and keyboard Wave

If this is mouse is wireless, you need to replace both Mouse and Reciever. Wireless mice only work with the Rx that comes with it.

http://www.ebay.com/itm/Logitech-Wave-Keyboard-W-Reciever-and-2-Mice-See-Description-/281506537027?pt=LH_DefaultDomain_0&hash=item418b18de43
Look at this.

Hi

For download the driver for your USB tower click hear.

Hi,

There are several different methods in resolving this issue. Before you perform these methods, make sure that the battery of your cordless mouse is fresh. Then, try this first method..
Method 1: Resynchronize your device with the receiver loadTOCNode(2, 'moreinformation'); To resynchronize the mouse or the keyboard with the receiver, follow these steps.
Note When you synchronize the mouse or the keyboard with the receiver, put the device near the receiver and put any other wireless keyboards and mouse at least 6 feet away.

1. Press the button on the receiver, and then verify that the light on the receiver starts to blink.
   
   Note Some newer Microsoft devices are permanently bound to their receiver and cannot be reset. If your device does not have a button, skip to Method 2.
2. If a dialog box appears on the screen in several seconds, follow the instructions that appear on the screen. Otherwise, go to the next step.
3. Press and release the Connect Channel button on the bottom of the mouse or the keyboard.
4. Check the green light on the receiver. A steady green light means the synchronization was successful. If the problem persists, try steps 1 through 4 again.
5. For the Wireless Notebook mouse: This issue can occur if the micro-switch on the bottom of the mouse is not released. Use a pin or a pen to try to release the button if it is depressed.

The following example shows the buttons to push to synchronize a wireless hardware device


Method 2: Install the latest software loadTOCNode(2, 'moreinformation'); Download and install the latest Microsoft IntelliPoint and/or IntelliType software. For more information, visit the following Microsoft Web site:
http://www.microsoft.com/hardware/download/download.aspx?category
I hope these works for you. Should you need the other methods, kindly reply for follow up.
Good Luck!

Mongkey
"Understanding explains better..."

have you tried changing the battery in the mouse

Hello i hope u 'll be fine.... thanks for usingfixya.

Try this service manual for Cordless Desktop Wave Keyboard and Mouse

• To download just Click Here
• You can also download it from Here
  

Download it and Enjoy
You can also see lots of effective information of your product from this.

• Manual is in pdf format if you have no Adobe Reader software which support pdf files then Download it from here Adobe Reader

Just watch this video, It 'll be also helpful for you.
Enjoy I hope this solution will very helpful 4 u. Best of luck
Please keep thumbs up in do rating
THANKS & Keep using fixya

www.logitech,co,uk enter your specs and download updates

it should install automatically as most are plug and play.
connect the USB with the wireless piece into USB port it should then invoke found new hardware etc. if it cannot find a driver o to the HPS site tech support area and find the software driver to suit

If you are looking for product/user documentation, you can find it here:

http://www.microsoft.com/hardware/documentation/default.aspx?type=Sets&sku=4GC-00002

If you are looking for installation software/drivers, here:

These are the drivers for Windows XP:

http://www.microsoft.com/hardware/download/DownloadResult.aspx?category=MK&type=Sets&name=pd_wld4000&os=XP_32&lang=en

And for Vista 32bit here:

http://www.microsoft.com/hardware/download/DownloadResult.aspx?category=MK&type=Sets&name=pd_wld4000&os=WVista_32&lang=en

For other OS's, I can give link if needed.

Best of Luck!

If you have the Setpoint software installed from logitech, it will show onscreen when you press caps lock.  eg CAPS LOCK ON, or CAPS LOCK OFF when the key is pressed

You probably already done this but try pressing the receiver button and while it is flashing turn the board over and press the small reset/connect button on the bottom of the board and also the reset/connect button on the bottom of the mouse. It should work okay after that. here is hoping that helps. Bud