Heya! the numbers on my keypad is working properly but the top buttons(up,down,left and right arrows, the answer button) is not working at all.. what seems to be the problem?..pls help me. if you can send me tips on how to repair it so i will know if i can do it myself without going to a repair shop..thanks

The key combination you looking for to close any window or message in a Windows environment is ALT+F4, depending on the type of keypad the Motorola MC3190G are using.

Please Note: Keypad functions can be changed by an application so the mobile computer keypad may not function as described.

48-Key Keypad

The ALT functions are indicated in blue on the keypad, so in order to use these, you have to activate the ALT Functions first by pressing the BLUE BUTTON (FUNC) (Right side below ENTER button) and then press the CTRL BUTTON (left side below BKSP button).

After the key combination is pressed, the ALT icon appears on the taskbar on WinCE devices or the ALT icon appears at the bottom of the screen on Windows Mobile 6.5 devices.

Now you can press the "D" button to use F4, this will close any window or message that is currently in view.

38-key Keypad

Press the blue FUNC BUTTON (Right side below RIGHT ARROW button), and then press CTRL button (Middle below UP ARROW button), now you can press the F4 button.

28-Key Keypad

Press the blue FUNC button (Bottom right next to Power button), and then press the CTRL button (Top right side below RIGHT ARROW button), now you can press number 4 to use F4.

Hope this helps, good luck.

Can you still send fax? if sending and receiving are not working you can try to update or uninstall/reinstall the software for this unit..

Hope that helps.............

How to Change the Brightness of the Display

To darken the display, press the yellow 2nd button and then press and hold down the Up-Arrow button located in the upper right section of the keypad. Release the Up-Arrow button when the display has reached the desired level of darkness.

To lighten the display, press the yellow 2nd button and then press and hold down the Down-Arrow button. Release the Down-Arrow button when the display has reached the desired level of lightness.

As you go through this process, a number will appear at the top right corner of the display. If this number is 7 or higher when your screen reaches the desired level of brightness, then your batteries are getting low and may need replacing soon. This number will be approximately 3 or 4 for new batteries.

Hi,

Follow the instructions below to set date and time on printer

Setting the date and time on an HP All-in-One Follow these steps to set the date and time from the control panel.

1. Press Setup .
2. Use the right arrow button ( ) to highlight Tools , and then press the OK button.
3. Select Date and Time from the Tools menu and then press the OK button.
4. Enter the month, day, and year by pressing the appropriate numbers on the keypad. After the date is entered, the Enter Time screen displays.
5. Enter the hours and minutes by pressing the appropriate numbers on the keypad. After the time is entered, the Tools menu displays.
6. Press the Back button to return to the main menu.

Follow the steps to solve "Unable to Recieve Fax" Issue
Basic requirement are..
1. Rings to answer should be 2 rings greater than your Answering machine rings or Voice mail ( set it to 6 instead )
2. Auto Answer should be on
3. Turn off ECM ( Error Correction Mode )

Use these steps to change the Rings to Answer setting.

1. On the product control panel, press the setup button ( ).
2. Use the right arrow key ( ) to select Basic Fax Setup and then press the OK button ( ).
3. Use the right arrow key ( ) to select Rings to Answer and then press the OK button ( ).
4. Use the right arrow key ( ) to select the desired number of rings and then press the OK button ( ).

Make sure that the Auto Answer feature is turned on When the Auto Answer feature is on, the HP fax product automatically answers incoming fax calls. When off, the HP fax product does not answer any incoming fax calls. To turn on the Auto Answer feature, follow these steps.

1. Press Auto Answer on the product control panel. When the Auto Answer button is lit, the feature is turned on.
2. Try to receive a fax.

Make sure that ECM is Turned Off ( Error Correction Mode )

1. On the product control panel, press the setup button ( ).
2. Use the right arrow key ( ) to select Advanced Fax Setup , and then press the OK button ( ).
3. Use the right arrow key ( ) to select ECM , and then press the OK button ( ).
4. Use the right arrow key ( ) to select Off , and then press the OK button ( ).

Try to Receive Fax Now.

These steps should resolve the issue and you should be able to receive fax

Thank you for contacting FixYa Team


* Please rate this solution with Thumbs up and comment to help us improve providing support

Finalising a disc enables the disc to be played on any other compatible machine. By doing this it changes the disc format so that you can no longer record to it turning it into a Play Only disc. On your Panasonic DVD Recorder you can record to many (if not all depending on the model) of the following DVD Disc formats to the limit of their capacity over multiple occasions. The disc in question can be played back and recorded to on the DVD Recorder during this time but until it is finalised it will not work on any other machine.
DVD Formats: DVD-R, DVD-RW, DVD-RAM, DVD+R, DVD+RW.
How do I Finalise my disc?

1. When you have finished the initial recording stop the disc and press the ~FUNCTIONS~button.
2. Using the ~UP, DOWN, LEFT, RIGHT arrows~ on the keypad select "To Others" and press~ENTER~.
3. Using the ~UP, DOWN, LEFT, RIGHT arrows~ on the keypad Scroll down to "DISC MANAGEMENT" and press ~ENTER~.
4. When the disc management screen opens you need to use the ~UP, DOWN, LEFT, RIGHT arrows~ on the keypad to scroll down to "FINALIZE" and press ~ENTER~.
5. Using the ~UP, DOWN, LEFT, RIGHT arrows~ on the keypad select "YES" and press~ENTER~.
6. Using the ~UP, DOWN, LEFT, RIGHT arrows~ on the keypad select "START" to begin finalizing the disc, please note by pressing start here you will no longer be able to record or edit the disc being finalized.

Finalizing may take up to 15 minutes.
Do not disconnect the mains power in this time. A message appears when finalizing is finished, press the enter button when this appears. It will now play on other compatible machines.

Change the ring count on the fax when the receive mode is set to Fax/Tel or FaxOnly modes. Change the ring count on your answering machine when it is connected to the fax and the receive mode is set [Ans mc connect] (Answering Machine Mode).

1. Press the <FAX> button to enter the Fax menu.
   
   
2. Press the <Menu> button.
   
   
3. Press the left or right arrow button to select [Maintenance/settings], then press <OK>.
   
   
4. Press the left or right arrow to select [Device settings], then press <OK>.
   
   
5. Press the up or down arrow to select [FAX settings] (item <1>), then press <OK>.

6. Press the up or down arrow to select [RX settings] (item <3>),
then press <OK>.

7. Press the up or down arrow to select [Incoming ring], then press
<OK>.

8. Press the up or down arrow to select [ON], then press <OK>.

Note: The default setting is [OFF]

1. 1. A window will appear displaying the number of rings before the machine will answer. Press the up or down arrow to select the number of rings (from 1 to 30 rings).
      
   2. Press <OK> to set the number of rings.

9. Press the <Stop/Reset> repeatedly to return to Fax standby
mode.

I hope this helps.

Cindy Wells

NOTE: The following solution applies only when the WorkCentre has the fax feature.

Speed Dial numbers must be set up before creating a Group Dial. If Speed Dial numbers have not been set up, See the Related Items below for additional information.

1. Press the [Machine Status] button on the Control Panel. 'Machine Setup' will be displayed on the Display Screen.
   
   
   
   
2. Press the [Up] or [Down] arrow button until 'Fax Setup' is selected, and then press the [Enter] button.
3. Press the [Left] or [Right] arrow button until 'Group Dials' is displayed, and then press the [Enter] button.
4. Press the [Left] or [Right] arrow button until 'New' is displayed, and then press the [Enter] button.
5. Enter a Group Dial number between 1 and 200 using the numeric keypad, and then press the [Enter] button.
   
   NOTE: If a 'Location No. is Registered' message is displayed, the number has already been stored as a Group Dial. Enter a number that has not been stored, and then press the [Enter] button.
   
   
6. Enter a Speed Dial number to be added to the Group Dial using the numeric keypad, and then press the [Enter] button. The name and fax telephone number stored for the specified Speed Dial number will be displayed.
   
   NOTE: If a 'Not Assigned Enter Again' message is displayed, the number has not been stored as a Speed Dial number. Enter a number that has been stored, and then press the [Enter] button.
   
   
7. Press the [Enter] button. The Speed Dial number will be added to the Group Dial.
8. Repeat steps 6 and 7 to add additional Speed Dial numbers to the Group Dial.
9. After all required Speed Dial numbers have been added to the Group Dial, press the [Menu / Exit] button.
10. If required, enter a name for the Group Dial using the corresponding buttons on the numeric keypad, and then press the [Enter] button. If a name is not required, press the [Enter] button.
11. Press the [Stop] button to return to the Standby mode.
    

Make sure Auto Answer is turned on or is currently within the scheduled on period...... On the main screen in Fax mode, use the up and down Arrow buttons to Auto Answer...... Using the left and right Arrow buttons... Select...... to scroll... choose Yes or Scheduled and press... If you selected Scheduled, the Auto Answer Schedule screen appears...Using the keypad, specify the time you want Auto Answer to be turned on and be turned off

Hi,

Please follow the steps given below to check wheather the error correction is turned off.

You need to disable "Error Correction," please follow the steps given below:
1. Press "Fax Mode."
2. Press "Menu."
3. Press "Up" or "Down" Arrow button repeatedly until "Ringing and Answering" is highlighted.
4. Press "Select."
5. Press "Up" or "Down" Arrow button repeatedly "Error Correction" is highlighted.
6. Press "Right arrow" or "Left arrow" button until "OFF" appears.
7. Press "Select."

Please follow the steps given below to recieve the fax:

1. From the control panel, press "Fax Mode."
2. Press the "Menu" button once.
3. Press up or down arrow repeatedly until "Ringing and Answering" is highlighted.
4. Press "Select."
5. Press up or down arrow repeatedly until "Pick-Up On:" is highlighted.
6. Press left or right arrow to choose an option.
7. Press "Select."
If you want to set a schedule to turn "Auto Answer" "on" or "off:"
1. Press up or down arrow repeatedly until Auto Answer Scheduling is highlighted.
2. Press left or right arrow until "On" appears.
3. Press "Select."
4. Press down arrow button to select the time for "Auto Answer On."
5. Use the keypad to enter the date and time. Press 1 for AM, 2 for PM, or 3 for 24-hour mode.
6. Press down arrow button to select the time for "Auto Answer Off."
7. Repeat step 5.
8. Press "Return" button to save the settings and exit the menu.
9. Make sure the "Fax Auto Answer" light is on.
When the number of rings you set is detected, the printer automatically receives the incoming fax.

To scan a document, please follow the steps given below:
1. Go to "Start," "Programs," Lexmark printer, "Lexmark All-in-One Center."
To see how an image will look after it is scanned, click "Preview Now."
2. Click "Scan," "Send scanned image to."
If scanning an image, choose a graphics program such as "Lexmark Photo Editor," "MS Paint," etc.
If you wish to "Scan to OCR," choose a text program such as "MS Word," "WordPad," etc.
Once the image is scanned, the "Abbyy OCR" software will open automatically.
3. To begin the scanning process, click "Scan Now."
4. To view the additional options, click "See More Scan Settings."
To indicate what type of image is being scanned, select the "Option" next to the type of object you are scanning. Your settings will be optimized for that object type.
To indicate how the scan will be used, select the relevant option from the menu. Your resolution and other settings will be optimized based on your selection.
5. To revert back to the normal All-in-One main page, click "Hide Extra Scan Settings."
6. Under "Display Advanced Scan Settings"; you can see change settings, which will affect the outcome of your scan.

Push the top left button (looks like an audio tape).
Then push 9
It will display a 180second count down in which to record your voice message.
When finished, push the top right button (looks like and arrow into a diamond).

To turn off/on the answering machine:
I lost my user manual for my Doro 615R+1 home phone, so after much deliberation and playing with many buttom combinations, worked out how to turn off the answering machine.
- Open the answering machine function by pushing the top left button (looks like an audio tape).

- Push '0' and then use the up and down arrows to select On or Off.

- To enter your selection push the top right button (looks like and arrow into a diamond).

Done :-)