Question about Mitsubishi WS-55809 55" Rear Projection Television
The model number you indicated: WS-55809 does not use the STK-392-110--IT USES TWO STK-392-570 CHIPS.
IF WHATEVER SET YOU HAVE USES A STK-392-110 YOU CAN USE THE STK-392-150 TO REPLACE IT--it is a higher current device than the 110 chip---there are some others even stouter but some create more problems.
I have used the 150 chip on several sets for the 110.
If this information helps you rate this solution as I do this here for FREE.
Posted on Nov 15, 2009
Testimonial: "That was very helpful info.Will use chips. couldnt make up my mind if safe to use. Thanks a million. "
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: stk392-110 chip replacement
stk392-110/150/180 all have same fit, form function except the 150's and 180's are basically upgrades for they're more stable (more heat tolerant than the original 110's); I'd buy the 150/180 myself; you can get the stk392-180 for just under 10 bucks on eletronix.com.
Posted on Apr 20, 2008
I have no experience at tv repair but I solved this problem and you can too. I bought 2 stk 392-150 chips made by sanyo on ebay for $30. I bought a low life jewelers loupe which is a sort of cap with different lens pieces out on the end of the bill for $10 on ebay. I bought a soldering iron and the smallest diameter silver solder and a little suction bulb and heat sink grease from radio shack for $20.
Take the back off tv. Locate circuit board with ics. remove screws that hold board . there are several wire bridges, snap these apart also. number connections with marker, undo connections. you will note that this board is connected to 3 crts by cable, do not disconnect this cable! This board must remain connected to crts by this cable! (so much for tv repair.com telling you how easy you can remove the board and solder it in your workshop) this board must remain connected to the crts, you can flip the board upside
down but all work must be done at back of tv
undo screws on ics. pry ics loose from heatsink. put on jewlwers loupe then turn board over and heat up each ic pin then **** molten solder into suction bulb. each ic has 19 pins. remove old ruined ics ( shame on Hitachi) my tv was only 3 years old! Put gob of heatsink grease on new ic, spread with razor blade, not to thick or thin, stick new ic thru holes in board and screw to heatsink . solder all pins to circuit board. look at the resistors that are close to the ics. if one is burned black it will have to be replaced, they act as circuit breakers and will burn out to protect other parts of the tv. usually the resistors are fine it was just the cheapshit hitachi ics that were bad.
Put everything back together and turn on tv for 20 min. after 20 min do the magic focus. your tv should focus up and be good as new. I have fixed several hitachi 51g500a in this way. Good luck!
Posted on Sep 21, 2009
Tips for a great answer:
Feb 10, 2015 | Facebook Apps
Oct 19, 2014 | MITSUBISHI DIGITAL ELECTRONICS MITSUBISHI...
Jul 25, 2014 | Magnavox 32MF301B/F7 32 in. LCD TV
Feb 10, 2014 | LG 42LH90 42 in. HDTV LCD TV
Dec 23, 2012 | Hitachi 53UDX10B 53" Rear Projection...
Feb 15, 2010 | Televison & Video
Oct 17, 2009 | Hitachi 43FDX01B TV
Jan 01, 2009 | Philips Magnavox 51MP392H Rear Projection...
Mar 24, 2008 | Panasonic PT-51HX41 51" Rear Projection...
Sep 26, 2007 | Sony KP-43T90 43" Rear Projection...
Mar 17, 2016 | Mitsubishi WS-55809 55" Rear Projection...
574 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: