Question about Code-Alarm Code Alarm Transponder

1 Answer

Motion detectors dont' work

We have 3 dual tech motion detectors. They all have power to them but none of them work.They seem to have red,orange , and green lights. They light up when you walk in front of them but usually only orange in color. They just don't set off the alarm. we can't find a model number on these

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 3,733 Answers

I have a chipper and it started giving lot of problems 4 yrs ago, so I got this free Pdf manual from reliable-store for free and I don't think Ive visited a mechanic or fixya for help for more than 3-4 times out of the 20 times I fixed the chipper in these 4 years

Posted on Jan 23, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
MNfisherman
  • 11896 Answers

SOURCE: 1995 Ford Windstar Speaker Coding Scheme.

www.installer.com as speaker schematics

Posted on Jan 17, 2009

haider_alhar
  • 90 Answers

SOURCE: no power to alternator green/red wire on dash light

alternator drived mechanically by a belt receiving energy from the crank shaft . and it chargs the battery , so your battery dead or the cables nedd to be replaced

Posted on May 31, 2009

oldfishead
  • 155 Answers

SOURCE: 1997 mustang rear running lights dont work front

assuming you have brake lights and marker light, I would check the socket for voltage, both the contacts and probe the wire (Brown) for voltage...it could be a bad socket.... if no voltage, trace the "Bwn" wire back and keep probing til you find voltage, check the connector in the trunk on the LT/RT side also...hope this helps you...GL

Posted on Jul 08, 2009

  • 13 Answers

SOURCE: reverse lights dont work.escort van.1.8 none turbo.2002.

With engine off and key on, emergency brake set, place the gear selector in reverse, using a volt ohm meter check for voltage at bulb terminals. If voltage is present then the switch is working and the wiring to the lamp is good. Next check the other terminal with the ohmmeter to ground for connection. Sounds like a bad ground.

Posted on Jul 30, 2009

Testimonial: "a great help.problem solved"

  • 714 Answers

SOURCE: dash lights work, but chuster lights don,t

i had to disconnect the battery and reconnect on my daughters car and that solved her problem, worth a try!

Posted on Jan 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do you have a wiring diagram to wire a security motion detection light between 2 3-way switches so switches can be turned: (on-Motion)/(on- Completely) from 2 differemt locations?


One of the switches needs to be a 4-way then the PIR will act as any other switch. The downfall is if the lights are on and motion is sensed they will turn off.

My preference is to connect the contacts of the security device across the travelers of the three way circuit. The travelers are probably the red and black in the three conductor cable. When motion is detected the lights will turn on regardless of the settings of the three way switches then after timeout they will turn off. If they are turned on with one of the three way switches nothing will happen when the motion detector turns on except you cannot turn the lights off until the security device has turned off.

I hope this helps. The motion contacts need to be isolated from the motion detector power.

Feb 20, 2014 | Electrical Supplies

2 Answers

Hi my question is motion spot light has has two black wires one from each light and two white from each light and one red from the motion detecter which is connected to the black wires there are two wires...


The red wire from motion detector connects to both of the black wires from the lights. The black wire from the motion detector connects to the incoming black wire from the switch or source. The white wire from the motion detector connects to both of the white wires from the lights and to the incoming white wire from the switch or source (all white wires are under one wirenut).

Dec 18, 2010 | Home

1 Answer

I am trying wire a motion Senior its has 3 wires coming out the back red white black


To connect a separate motion detector to a light fixture (and assuming the fixture uses incandescent or the newer twisted florescent light bulbs), the RED wire from the detector is attached to the black ("hot") wire from the fixture; the WHITE wire from the detector is attached to the white wire from the power source; the BLACK wire from the detector is attached to the black ("hot") wire from the power source. Sometimes the white and black wires from the power source are mixed up, reversed. So it is best to check to determine which wire is actually "hot" (shows voltage in a meter between the wire and the ground wire or the metal box the power wires come from). In general, a colored wire (often black) in the power source, if wired properly according to accepted custom, will be "hot" and 120v in US. The white wire in the power source is called the "neutral" and should be neutral with the ground wire and/or the metal box. If there is another colored wire in the power source (often red) and if it is not taped with some black tape (to indicate it is really a black wire), then it too may be a 120v. hot wire, but it may also be an 120v. hot wire that is 120v opposite the other 120v wire. That is, one 120v wire is 120v+ and the other is 120v- The difference in voltage between these 120v wires + and - is, hence, 220v. If you see multiple colored wires, it is also a good idea to check the voltage between them to know if you are dealing with a power source that entails 220v. In short, you want to know what you are doing, obviously for personal safety, but also to accomplish what you want... to properly connect the motion detector.

Dec 12, 2010 | Home Security

1 Answer

Two SM120X not always compatible on same circuit.


I would pose this question directly to the manufacturer. I'm kind of surprised that the AHJ would approve such a configuration to begin with, as I would not have thought such interconnection would meet the intent of the code for notification, but then I don't know all the circumstances. I would ask Kidde directly.

Jul 20, 2010 | Kidde Relay Module for Smoke Alarms

1 Answer

How to wire a cooper industries 6107 3-way motion detector switch


I opened the box and traced the lines to see which are connected
when the switch is turned on and I left the red wire disconnected.

Jan 28, 2010 | Cooper Wiring Devices Motion Sensing...

1 Answer

Lights only work in test mode sensor picks up motion


You are talking about a motion detector attached to some type of light I presume. Your numbers mean nothing, I'm sorry to day.

Very first consideration, you do have it correctly wired, right? White to white - black to black - green to green and ground. The red goes to the lamp black wire, right??? (Light White goes to neutral (white line))

I am very familiar with motion detecting lights, working at a large resort at the seashore.

Two conditions that must exist for this light to come on ... it must be dark and there must be a motion. There should be two adjustments on your detector; one is for sensitivity and the other is time the device should remain on.

Dark ... not just sundown ... are there other lights in the area that may cause your detector to think it is day time?

Sensitivity. On minimum sensitivity, your detector is nearly blind to any but the closest movements. On maximum, it will probably see bats flying by. You must adjust to meet your needs.

Does it have a warranty? I dont know. You would have to check the information that came with your light.

I hope this information helps you ... Positive comments are appreciated.

Thanks for clarifying your question and thanks for visiting FixYa.com

a



Oct 27, 2009 | Electronics - Others

1 Answer

Dsc sensor not operating properly. I want to change it, is this very difficult? Thank you.


You don't mention what type of sensor. I assume it is a motion detector. Before replacing I would strongly suggest you first remove all power from the system by disconnecting the backup battery inside the control panel then pull the system's power transformer which should be plugged into an electrical outlet nearby. You will know that all power is removed by looking at the keypad - all lights on the display are off. Next remove the motion detector's front cover. Some detectors have a small screw on the bottom so that when removed the cover pops off. Others need to be opened using a flat blade screwdriver and prying off the cover. Once the cover is removed there should be a 4 conductor wire that is wired to a series of terminals. Observe the polarity of the wires, disconnect them and remove wall mounting screws. Install new unit. Be sure when wiring to connect power wires correctly. The 4 conductor wire should have a red (positive) wire and a black (negative) one. Connect the red to the + or pos terminal and the black to the - or neg terminal. Read the instructions that came with the new unit if in doubt. When finished plug the power transfomer back in then reconnect the battery (in this order). If power is connected properly the motion detector's red walk test light (indicating motion) should light whenever you walk in the protected area. Also make sure the system recognizes motion by first closing all protected areas such as windows and doors to get a system ready or green light indication on your keyad, then walk around the protected area. A properly working detector will show you a fault on the keypad everytime the system senses motion.

Sep 11, 2009 | DSC Home Security

1 Answer

How do I get into the program mode to activate motion detector


Remove the mounting plate (on the back) and press the button, or trip the tamper.

Jan 30, 2009 | GE Security Simon 3 Wireless Home Security...

1 Answer

Electrical hook up for 2 motion detector lights so both lights operate when either detector is activated (dual master system)


yu can't do it with off the shelf detector. Sine the detector is single input.
you need serial and parallel input to the device.
you need to get commercial detector that haev serial and parallel input to the detector.

Dec 15, 2008 | Solar Motion Security Light Conversion...

1 Answer

How do i set my simon 3 motion detector?


You have to put the motion in sensor group 17. You will see this list near the back of the thick installation manual that came with your Simon. Also, when installing the motion, when it asks you to trip the button on the sensor, all you have to do is take the back off of the motion. You will hear a beep. Replace the back, and continue!

Oct 20, 2008 | GE Security Simon 3 Wireless Home Security...

Not finding what you are looking for?
Code-Alarm Code Alarm  Transponder Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Vehicle Parts & Accessories Experts

xxxxxx xxx

Level 3 Expert

5013 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14610 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22441 Answers

Are you a Ford Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...