Lights on Rechargable Lantern.. Swissgear SG66301

Unfortunately nowhere. If you look by the charging port, there is often a sticker that shows volts, amps and polarity. With that you can buy from Amazon or eBay.

https://www.google.com/search?q=SwissGear+lantern+SG66301+AC+Adapter

..

1. VR2/VSI DIAGNOSTIC FLASH CODES

# OF LEDS
CODE
CAUSE
POSSIBLE SOLUTION
One red LED
1
Low battery voltage
Charge batteries
Two red LEDs
2
Left motor open
Make sure left motor is plugged into controller.
Three red LEDs
3
Left motor wiring fault
Contact your authorized Pride Provider.
Three red LEDs One yellow LED
4
Right motor open
Make sure right motor is plugged into controller.
Three red LEDs Two yellow LEDs
5
Right motor wiring fault
Contact your authorized Pride Provider.
Three red LEDs Three yellow LEDs
6
Inhibit active
Contact your authorized Pride Provider.
Three red LEDs Four yellow LEDs
7
Joystick error
Contact your authorized Pride Provider.
Three red LEDs Four yellow LEDs One green LED
8
Controller error
Contact your authorized Pride Provider.
Three red LEDs Four yellow LEDs Two green LEDs
9
Brake fault
Make sure both motors are plugged into controller.
Three red LEDs Four yellow LEDs Three green LEDs
10
High battery voltage
Contact your authorized Pride Provider.
What if the speed LEDs on the VR2/VSI begin to flash?

• Determine if the battery charger is connected to the power base. When the battery charger is connected to the power base, a charger inhibit feature keeps the power chair from driving. This is indicated by the VR2/VSI speed
  LED(s) flashing.
• Determine if the charger harness fuse has blown. A blown charger fuse can cause the charger inhibit to
  activate.
• Determine if all controller connections are plugged into the power base properly. If the 3-pin charger
  inhibit connector is not plugged in properly, then the charger inhibit feature will activate.

There are several different models of the Swiss Gear rechargeable lantern. On most though, you can remove the top portion of the lantern and check the lighting element inside. In most cases the elements can be removed and replaced. I have a dual filament lantern and from experience I know that every so often you may have to go buy a replacement light piece. If the lantern has been bumped or even just strapped to the outside of the pack while walking, it's possible for those elements to become loose and need repositioning or replacement so do check that. I'm sure that it should be unlikely your charger is malfunctioning unless you left it plugged in for some very extended period of time, in which case I would say the light would be more likely to burn out. But definitely try that and if that doesn't work the battery pack on the lantern itself may have an issue in which case you can always get a replacement.

The adapter need to match the charge voltage requirements of the battery in the Swissgear lantern.
This voltage maybe written on a label on the lantern.
i suggest go to the shop where you purchased the lantern for the charge adapter.

Alternate Red and Green flashing means bad battery. Buy a new one, or take it to a Makita Service center for replacement if it's under warranty.

Normally the yellow light indicates hot battery, but it could also mean dirty battery contacts so the heat sensor can't be read, or that the fan is clogged with dust and unable to cool the battery. The manual says let the battery cool and try again. If the yellow still flashes, it's contacts or the fan.

Read the manual online at:
http://www.makita.ca/data/upload/accessorypbim/417_im_english.pdf

I just bought a retro rechargeable sealed battery,recently. I charged it for 18 hours,the lights all worked,but I don't remember the green light comming on.i put the lantern away for 3 months or so.i decided to check the the battery light out first week of june, the light was there,then I said let me charge it up again, I never seen any green light come on showing it was fully charged. I took the battery out and checked the wires to see if there was a break. None that I could tell. After you take the battery out ,there is another section square that covers where the bulb is located,but I didn't touch that part yet. Stuck" on this one. Help"

According to the owners manual for these swimming pool lights, this is what each colored indicator means. Hope this helps.


Solid green
The battery pack is fully charged.
Slow flashing green
The battery pack is almost fully charged.
Slow flashing yellow
The battery pack is half charged.
Medium flashing yellow
The battery pack is less than half charged.
Fast flashing yellow
The battery pack has almost no charge.
Fast flashing red
A charging error has occurred and the light should be unplugged and then plugged back in. If the Fast Flashing Red persists after several attempts, the battery condition is questionable.



Also in the trouble shooting guide, it mentions this:


Problem: Red Indicator Light Is Flashing While Charging

Solution:
A red flashing indicator light when charging indicates a selftest
error condition. Unplug the product and plug it in again.
Try this several times; if the indicator light continues to flash
red, unplug the GlowBuoy and take it to an authorized service
depot.

bad battery

I would go to Radio Shack and have them explain the proper charging procedure as well as inquire about the red and green lights as not all chargers go green when fully charged-Normally red indicates a charging action and if a charger has no fully charged light, then a required charge time period is noted in the instructions. Batteries can be ruined by over charging!

the 3 beeping sound means that the camera has low battery capacity. the lens is stuck out because there is incorrect battery connection. there is an option on the camera setting for the battery type. try this one:
-turn the camera on
-click on Menu button
-select options using left/right, up/down button
-select Set up 2
-Select Battery type
-Select Alkaline for non-rechargable
or Ni-MH for rechargable
-click OK button

this setting should be done when using camera for the first time and whenever you are switching battery types, from rechargable to non-rechargable and vice versa.