Question about Dryers

1 Answer

Flame will come on at first start then will run for a few mins then turn off then ignition will come on but gas will not turn on

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 73 Answers

Cool you recognize the fact that the igniter is turning on you are obvisouly tech savy so I will dispense with the usual amenities and give you a technicians answere.. igniter gets power and when it reaches max current opens gas valve as time goes on igniter still glows red but doesn,t generate enough current to open gas valve change the igniter first (cheap) if it doesent work check your gas pressure ( need a guy with a special meter) if pressure is too high ( not very common) valve has trouble over comming pressure to open if pressure is ok then time to change out main gas valve Good Luck

Posted on Oct 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My York furnace sometimes doesn't completely ignite


A noisy inducer probably is headed for replacement.

The igniter can produce a healthy glow and still be defective. Mine had to be replaced with a new, improved one.

The thermocouple could be defective even though it seems to open the gas valve when it should.

The heat sensor in the bonnet could be defective. That controls main blower operation.

The heat exchanger could be cracked.

Jan 10, 2014 | Heating & Cooling

1 Answer

Dryer starts hot surface ignitor comes on gas valve opens i get a flame 5 mins flame shuts off hot surface ignitor repeats and tries to ignite no flame after unit is off for 20 mins to 30 mins off unit...


Hi, If you are having problems with your gas dryer not heatingthe most common problem is that the ignitor goes bad. Even though it glowssometimes it is still not working properly. if you dryer is gas check out this gas no heat tip.... If you have an electric dryer, you can have many differentthings that can go wrong causing the dryer not to heat. check out this electric no heat tip...

heatman101

Sep 17, 2010 | Kenmore 77632 Gas Dryer

1 Answer

Our rheem gas pack running on propane will turn not always ignite


have you cleaned the flame sensor located on the
far left side of the burners?. Watch it go through the
cycles.

Igniter glows, gas valve turns on and gas ignites. If it gets that far and shuts down, it sounds like a dirty
flame sensor,clean it with sand paper.

Jan 10, 2010 | Heating & Cooling

1 Answer

Series 80 gas dryer. Turn on and flame only lasts few mins.


Intermittent contact inside one of the gas valve coils. Replace. Part number 279834.
You can order them at AP Wagner. Use coupon "New10" for 10% off

Oct 16, 2009 | Kenmore 75944 Gas Dryer

1 Answer

Kenmore gas stove not coming out of pre- heat model 66575842001


This sounds like a flame sensor problem. No signal from sensor will shut down gas valve. Check flame sensor position in flame/or replace

If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

Sep 02, 2009 | Kitchen Ranges

1 Answer

My kenmore dryer will start and run when cold after it heats up the flame (gas dryer)goes out then after 3 or 4 mins. i can see the igniter light but will not start a flame after 5 or 6 seconds the igniter...


gas valve coulkd be bad if not opening after a certain period of time the ignitor will turn off and attempt a few times more,does it have a soilenoid valve also open and clean any carbon that might be built up over yrs

Jun 21, 2009 | Dryers

2 Answers

Dryer does not dry clothes. Flame does not stay on


run dryer for 10 minutes then remove vent hose see if start working mean flame on for while, if it is then you need to clean your vent system.

May 01, 2017 | Maytag Atlantis MDG7400AW Gas Dryer

1 Answer

GE Spectra TrueTemp Oven Pilot is Out


REmove bottom panel from stove. shut gas off for at LEAST 5 min. Longer is better. Then placel open flame above gas nozzle, slowly turn to ignite posiiton. After it is lit, wait 30 seconds and turn to on positon.
If by chance this model doens't have a knob for this, then turn gas valve off for 5 min, let fumes evaporate, light flame, place over nozzle, turn gas on.replace bottom oven panel slowly.

Jan 18, 2009 | GE Profile Spectra JGBP90 Gas Kitchen...

Not finding what you are looking for?
Dryers Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dryers Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Craig Butler
Craig Butler

Level 3 Expert

1730 Answers

Brad Brown

Level 3 Expert

18072 Answers

Are you a Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...