Help with and f4 fault code on a fisher and paykel disher

Question edited for clarity, turn question around, add CAPS.

It is a motor stall. You need a technician.

Washing Machine - Top Loader Fault Code Numbers

Fisher & Paykel https://support.fisherpaykel.com > article > Washing-M... Sep 30, 2023 - 136, Motor Error - You will need a Service Technician to assist with this - Click Here to ... © Fisher & Paykel Appliances Ltd 2023. Loading.

Questions & Answers for: fisher paykel fault code 136

Fixya https://www.fixya.com > ... > fisher paykel fault code 136 Now Error code 136 means you have a motor stall ... Question about GWL11 Top Load Washer. 1 Answer · What is fault code 136 on fisher & paykel ...

I have a fisher paykel GWL11 that will fill and drain but

JustAnswer https://www.justanswer.com > Appliance Repair May 25, 2017 - If you had a 130 and a 136, the sensor is not likely the issue. Will the tub turn manually? How about lift up and down? Ask Your Own Appliance ...

1 answer · Top answer: Oh, that plastic nut will come off. See the link below. CLICK HERE

https://www.google.com/search?q=Fisher+%26+Paykel+GWL11+top+loader.+Fault+code+136

..

About the F4 error code on the Fisher and Paykel DD60DDFX9 dishwasher:
The F4 error code on your DD60DDFX9 dishwasher indicates a fault with the heating element or the temperature sensor. When the dishwasher encounters a heating fault, it is unable to heat the water to the correct temperature required for the wash and rinse cycles. This can result in poor cleaning performance and may also affect the dishwasher's ability to sanitize the dishes.
To troubleshoot the F4 error code, you can try the following:

1. Check the heating element: Use a multimeter to test the heating element for continuity. If the heating element is faulty, it will need to be replaced.
2. Check the temperature sensor: Test the temperature sensor using a multimeter. The sensor should show a resistance value of between 10,000 and 12,000 ohms at room temperature. If the resistance value is outside of this range, the sensor may need to be replaced.
3. Check the wiring and connections: Inspect the wiring and connections between the heating element and the control board. Make sure all connections are secure and free of damage or corrosion.
4. Check the control board: If the heating element and temperature sensor are both working properly, the issue may be with the control board. A certified repair technician will need to diagnose and replace the control board if necessary.

According to the owners manual that fault code is for a faulty temperature sensor or element. It also says to contact an Authorized Service Center. Hope this helps!

F4 implies a problem with water heater not working or temperature sensor giving wrong value. Check if the drawer is cold or too hot at the time of the error.

No temperature increase has been recorded when the element is on.
The element is not connected.
The element has gone open circuit.
Temperature sensor or electronics ADC has failed.

F4 fault is a a heat sensor problem,
http://www.retrevo.com/support/Fisher-&-Paykel-DD603SS-Dishwashers-manual/id/1012ag921/t/2/ Above is your manual, below is a DIY troubleshooting site ti help you isolate your issue and fix. Dishwasher Repair Guide: How To Fix a Dishwasher - ACME HOW TO.com

http://www.docstoc.com/docs/25379715/Fisher-_-Paykel-Washer-Diagnostic-Fault-Codes/
A;; fault codes above.

F4 fault would inidicate the temperature sensor that senses the water temperature is faulty or the heating element is not working.

Looks like you will need a technician to visit and have a look.

You can get fisher paykel service manuals here:
http://fisherpaykelparts.net/index.php