I just bought the new Whirlpool Duet Steam Dryer. It starts and then like 5 to 10 minutes into drying the machine starts beeping and adds time. It also seems to shut off randomly as I am running the dryer 3 times before they are dry. They are not big loads. At first I thought it was the door problem, but I don't know anymore. Thanks for any help!

Unplug for 1 minute. Plug back in. Check status

Whirlpool Duet GHW9150P Front Load Washer Beeping ...

www.fixya.com > ... > Whirlpool Duet GHW9150P Front Load Washer

Question about Whirlpool duet Washing Machines ... my front loader is not workingwhirlpool washer flashes and beeps will not finish a cycle 1 Beep/E10--Error: Water... It beeps through the wash and rinse cycle every couple of minutes. ... Cycle signal which tells you that the cycle is complete beeps through the entire cycle.

[PDF]front-loading automatic washer use and care ... - Whirlpool

www.whirlpool.com/.../U...

Translate this page Whirlpool Home AppliancesWash. This is the main portion of the wash cycle. You will see the washer tumble the load. ... Spin cycle. If the laundry is still wet, take half of the load out of the washer and try again. .... Using recommended AFFRESH® washer cleaner, add.

[PDF]DISHWASHER USER INSTRUCTIONS - Whirlpool

https://www.whirlpool.co...

Translate this page Whirlpool Home AppliancesThe first cycle using the sensor will run longer to calibrate the optical sensor. Rinse Aid. Using rinse aid will optimize your drying and wash performance. This dishwasher is ...... laundry detergent, hand soap, or dish detergent for hand washing .... models) you will experience more starts and stops throughout the entire cycle.

Continuous Beeping - Whirlpool Duet Sport Washer - The ...

appliantology.org > ... > The Laundry Appliance Repair Forum

It is possible you have a broken drum belt. You may need to call a qualified service man as changing a belt can be tricky.

Unplug the dryer for 30 minutes. Then reconnect the power cord to the outlet. This will reset the code temporarily. Unfortunately, the code means that the central control unit (clock) isn't communicating with the rest of the components correctly. You probably will need a new clock or dryer (depending on the warranty status). If the unit is under warranty, contact Whirlpool or the store where you bought the dryer (if it is brand new).
I wish that I had better news for you.

Cindy Wells

YOU NEED TO CLEAN THE VENT ON YOUR HOUSE IF THE BLOWER WHEEL IS BAD ON THE DRYER YOU WOULD HERE THE NOISE AFTER THE DRY STOPS THE BLOWER WHEEL WILL STILL TURN AND MAKE A NOISE

If it is brand new. It should have full factory warranty. I would called the place that you bought it from and have them fix it.

No truth to powder being better .fabric softeners on the towels is fine it does help keep them soft they just don't absorb moisture as well.. I belive you biggest issue is over drying the towels,use a lower temp setting on dryer and do Not trust auto dry settings for towels,expermint with timed settings, if towels are not dry you can always add a few more minutes,but over temp and over dry will stiffen and age them prematurely

Dear Customer

Please perform the following

• Check for proper air flow
• Check the ignitor
• Check gas jet
• Test the gas valve coils
• Check the flame sensor
• Test the safety fuse
• Test the thermostats
• Test the centrifugal switch
• Test the timer motor
• Test the temperature selector switch

please rate this,thank u

Brand new unit - same problem. After an hour of investigating, I found the issue.
You don't actually have to SLAM the door. If you look closely, there are 3 separate pins that must latch. One is a simple push-button style which latches no problem.
The others are little prongs at the top and bottom of door. The bottom prong latches cleanly, but the top one will not latch because the door is a bit too flexible.
Close the door normally, then firmly press on the top edge of the door. You will hear the final latch grab, then you press and hold the start button. The dryer starts normally.
Yay!

sounds like the door switch might be an issue,, does teh tub light go on /off as you open the door??? if not try manually pushing the switch in a few times.