Question about Air Tools & Compressors

1 Answer

I have a powercat airbrush and the gun has been taken apart

I have a powercat airbrush and the gun has been completly taken apart, I need to know how to put it back together

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 205 Answers

Ill need model and ser for the unit. thank you

Posted on Oct 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Air Brush blwa air out of tip but no paint. Whats up. Please help!!!


most common problem is paint, it is too thick, second problem is your feedline/needle block.

before you put your airbrush apart - remove paint from container, wash well with appropriate solvent, put some of this solvent to the container and try spraying, if no solvent comes out - adjust needle stopper, this is dual action! have needle adjustment! as you did not give the model and manufacturer, this can be only and only general advice!

if still nothing comes out - prepare butcher paper, disconnect airline from the airbrush, disassemble the gun putting the parts on the paper in order in which you disassemble it. wipe off the needle with soft cloth, use drop of solvent if needed. clean body and container assembly and check for liquid flow from container to the nozzle, it should be steady drop, if there is no flow, then use special brush and if you do not have one, soft copper wire of smaller diameter than the passage to clean mechanically the passage. check again for liquid flow. re-assemble the gun, use bit of vaseline or paraffin to grease the needle and moving parts before re-assembly.

use solvent first to check liquid flow. adjust needle, pattern and size of the max flow. remove solvent, put paint into the container and use normally.

in 0.2 nozzle, paint should be of virtually water density... if this is opaque paint - need to be strained as any impurities and bigger chunks will clog the outflow...

hope this advice will help you with your problem - and i do earn some points from you...

Aug 11, 2013 | Airbrushes 0.2mm Dual Action Gravity Feed...

1 Answer

How can I tell the difference between airbrushes and spray-guns?


Airbrushes are hand-held and used instead of a brush for detailed work. Spray guns can be either automated or hand-held and have interchangeable heads to allow for different spray patterns.

Feb 03, 2013 | Crafts & Hobbies

1 Answer

What is an air brush?


An airbrush is a small, air-operated tool that sprays various media including ink and dye. Spray guns were developed from the airbrush and are still considered a type of airbrush.

Feb 03, 2013 | Crafts & Hobbies

1 Answer

G22 airbrush is blowing air out of the cap and non is comming out of the tip wtf? checked everything, their is air comming out of the nozzil but no paint.. the cap keeps blowing off and the pain getting...


It sounds like you have a dirty tip. It doesn't take much to stop the flow to the tip. You need to take the tip completely apart to give it a proper cleaning. Just soaking it won't do.
Hope this helps but if not let me know and I'll try and trouble shoot further.

Jun 08, 2010 | Master Heaters MASTER AIRBRUSH MODEL G22...

1 Answer

Spraying paint instead of air for the first action


Make sure the needle is pushed completely up against the tip. You will possibly have to take the back handle off to adjust it. (I am not familiar with this paint gun specifically). Make sure you do not force the needle into the tip, gentley push it until it stops.
I hope this helps.

Nov 10, 2009 | RTO Dual-action Side-feed Trigger...

1 Answer

Blowing paint out trough cup


It is clogged and needs to be disassembled and cleaned with MEK. methyl ethel ketone 

Aug 01, 2009 | Air Tools & Compressors

1 Answer

Need a new paasche spray gun for bigger jobs


Anest-Iwata brand spray equipment has the most versatile line of airbrushes on the market. Im sure you will find one to meet your needs. well worth the money, it's all I spray

http://www.airbrush-iwata.com/

http://www.tcpglobal.com/airbrushdepot/iwata.aspx

check it out!!

Apr 07, 2009 | Air Tools & Compressors

Not finding what you are looking for?
Air Tools & Compressors Logo

Related Topics:

311 people viewed this question

Ask a Question

Usually answered in minutes!

Top Air Tools & Compressors Experts

John Trevino

Level 3 Expert

1407 Answers

Joe Garcia
Joe Garcia

Level 2 Expert

206 Answers

Brad Brown

Level 3 Expert

18060 Answers

Are you an Air Tool and Compressor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...