Hitachi 43FWX20B 43" Rear Projection Television Logo

Related Topics:

Posted on Oct 14, 2009
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

The color and focus is off - Hitachi 43FWX20B 43" Rear Projection Television

  • tom1501 Oct 14, 2009

    3D and purple and green

  • Anonymous May 11, 2010

    Does picture look 3d? red or blue out of place?

×

1 Answer

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points

Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

  • Hitachi Master 14,553 Answers
  • Posted on Oct 14, 2009
Anonymous
Hitachi Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

Joined: Jun 01, 2008
Answers
14553
Questions
3
Helped
2716367
Points
48227

OK--for a Hitachi this set is a little unusual---it uses two of the STK-392-120 CONVERGENCE CHIPS.

One or both are bad(usually just one) You need to replace both and any discolored resistors around them--all the resistors have location numbers and if any are even slightly discolored you need to replace them and both chips---You can buy a pair of these chips on Ebay for less than 13 dollars plus shipping.

If you remove the back cover (unplug the set first!) look at the circuit board on the far right side----about 4 inches wide and about 12 inches deep---the chips are on the far right side on the large metal piece with fins.

If you look and find any of the resistors behind them (on the left side of the metal with fins) discolored---note the location number printed on top of the circuit board under them (RK46 etc) and I can tell you the exact value of that part--most of the resistors that fail are low value and can be tested just like a fuse--It is important to find any bad resistors as if you replace the chips and miss any open resistors the set will still have the same problem.

THIS IS A EASY SET TO DO THIS REPAIR ON IF YOU KNOW HOW TO SOLDER---I CAN GIVE YOU INSTRUCTIONS IF YOU NEED THEM.

THIS KIND OF REPAIR TAKES ABOUT 1 HOUR--THEN YOU ADJUST THE SET WITH THE ORIGINAL REMOTE--set should be good to go without having this trouble for 5-8 years.

Let me know if this information helps you---If you are not able to do the repair let me know and I will give you advice


SD TECH

  • john May 23, 2011

    does anyone have schematic for this set. i need know which wires go where in the flyback transformer. thanks in advance.

×

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

2005 Ford Focus. Color code for rear wires to tail light and four seconds ZX.

USA car answer, you never said country

the license plate wire, to LED in turn new is here
OG/BLK

BK ON BOTTOM IS GROUND./

plate-undefined-undefined-0_0.jpg
0helpful
1answer

Colour code 2006 focus

2000 Ford Focus body color codes. Color Code(s) Color Description M6290A, MK Twilight Blue Metallic M6373A, UA Ebony M6640A, WT Performance White M6720A, TS Silver Frost Metallic
0helpful
1answer

Won't focus colors .. can see blue red green seperate ,, tried auto focus did not work

colors won't focus and I tried using auto focus. How do you correct the problem? How do you adjust the tubes?
1helpful
1answer

Will not color focus

Convergence amps need repair. Requires troubleshooting with meters, and soldering with new parts. A more common problem on RPTVs.
0helpful
1answer

Sony kp 57hw40 Convergence Problem The screen looks distorted, Letters or words on the screen are bowed.(I can see double but the screen is stationary all the color, hue, sharpness, brightness, exc. can be...

If after the Flash Focus™ feature has been performed, the colors on the FLASH FOCUS screen do no line up (converge), press the FLASH FOCUS button on the television to begin the cycle again. If the colors on the FLASH FOCUS screen continues to appear misaligned, service will be required .
NOTE: It is recommended to perform the Flash Focus™ feature about thirty minutes after the television has been turned on and keep the room as dark as possible.
1helpful
1answer

Will not show red color in picture, magic focus shows red though

You have a projection light element out. I had the green element go on mine. I had a service agreement so a repair tech changed it.
0helpful
1answer

Flash Focus does not focus the TV colors are seperated

if that doesn't work it will need new convergence IC's put in as well as a resistor or two

electech
0helpful
1answer

Setting color and focus inside case

The only way to do that is by eye. To Adjust the screen controls the best thing to do is turn them all down then slowly adjust one up until you get retrace lines (arched lines across the tv) then turn it down until the lines re not visible then go about 1/4 turn more, repeat this for the 2 remaining colors, after that its just done to eye for the best color. if you are still having trouble getting the color right you can go in the menu to the video settings and turn the color all the way down then you will have a black and white picture and you can adjust for a perfect black and white picture then turn the color back up in the menu.
As for the focus controls its best done by covering 2 of the tubes so you only have one color on the screen then adjusting to the best looking focus for that color. then repeat this for the other 2 tubes.
If you need more help or clarification please let me know

Tim
0helpful
1answer

Focus

Use the Setup menu to select English or Spanish as
the language for the menus and on-screen displays.
Adjust Color Balance Automatically or manually
(PerfectColor TM) using six colors, Magenta, Red, Yellow,
Green, Cyan and Blue. Reset the Color Balance to the
factory default settings. Align the focus (convergence)
of the TV's projected light beams or reset the focus to
the factory default settings.

0helpful
1answer

TOUCH FOCUS ERROR

The convergence IC`s need to be replaced and the related low ohm resistors need to be checked for proper value.
Not finding what you are looking for?

139 views

Ask a Question

Usually answered in minutes!

Top Hitachi Televison & Video Experts

Grand Canyon Tech
Grand Canyon Tech

Level 3 Expert

3867 Answers

matt martin
matt martin

Level 3 Expert

1259 Answers

Cindy Wells

Level 3 Expert

6688 Answers

Are you a Hitachi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...