Mp730 reset mp730 factory reset

To reset waste tank full error in MP730.

1. Press the "menu": Key
2. Press "Copy" Key
3. Press "#" Key

4. Scroll thru the menu headings until you come to "Test Mode" - 12th heading or select (-) as a short-
cut to the last setting.
4a. Press "Set" and the display shows:
Test Mode [1] - [8]
CF-FH3 :WLD-11-02

4b. Press "8" and the display changes to:
Test Mode [1] - [8]
Please wait

***note*** you have to wait until the display changes

Then the display changes to:
8: PRINTER TEST
[2]---[8]

5. Then Press the "3" button and the display shows:

8 - 3 : EEPROM Clear

*** the display scrolls to [0] : INK COUNT
[1] : 2PURGE FLAG

6. Press "0" button - for INK COUNT
7. Press the "Stop" button
8. Press Off then On to set new changes.
9. Printer feeds a blank page after it is turned on again.

This should Reset the printer and remove the WRONG CARTRIDGE error and save you a few dollars.

Try replacing all the ink absorbers and resetting the counter to zero.

It could be due to "waste tank full" alarm; you may need to reset the waste tank counter.
I found a reset sequence for a MP730 printer in this website that works for F30 and F50 as well. Try:
Resetting the Waste Ink Volume Counter

1) Enter SERVICE MODE.---
By pressing Menu-Copy-#

2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [OK] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

Skip step (6) since there is no [OK] key on F30 or F50 printers.

Press the reset button if they can correct that problem. Maybe you can used the not genuine cartridge on your printer or it could be not properly inserted your cartridge. Try to power off the printer and check your cartridge then power on it again.

#334 is an eprom error and if turning on and off does not reset it, you have something going on with the main logic board.
http://printer1.blogspot.com/2009/01/canon-multipass-mp730-service-manual.html
Above is a service and repair manual this will assist you to troubleshoot and hopefully repair, although I fear with this type of fault, it needs to be returned to the factory.

Hi there
Ok I have put a MP-Tools in my website for you to try out this tools are for reseting your inks plus it can do much more.

Click Link = http://www.4all2sell.com/reset-tools/MPTool.exe

All I ask is please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

All files on my website are only there for a limited

Hi you can try this.

To reset waste tank full error in MP730.

1. Hit the "menu": Key
2. Hit "Copy" Key
3. Hit "#" Key
4. Scroll thru the menu headings until you come to "Test Mode" - 12th heading
5. Hit the "3" button- this will bring up Eprom Clear
6. Hit "0" button
7. Hit the "Stop" button

Can only try then your printer go on longer but some time the other you need to clean out the waste ink it inside the printer go to open up all.



Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.

All The Best: Pineworks

Instructions for resetting the MP730 ink tank full counter
1) Enter SERVICE MODE.By
pressing MenuCopy#
2) Select TEST MODE. using the + key then the set
3) Select [8] PRINTER TEST in TEST MODE. by hitting the number 8
4) Select 3. [EEPROM CLEAR]. by hitting the number 3
5) Select 0. [INK COUNT]. by hitting the number 0
6) Let it default to the new value by waiting
7) Press the [Stop/Reset] key (returning to the state of 3)), this is the red stop key
8) Then press the [ON/OFF] key and the machine will reset and push through a page of paper

Sometimes is need to clean the purge unit

Canon MP730 Printer Purge Unit Disassembly and Assembly :
http://newsquaremusic.com/CanonMP730PrinterPurgeUnitDisassemblyandAssembly.pdf

http://newsquaremusic.com/CanonMP730PrinterWasteInkTankFullResolution.pdf

I hope this is useful

Try this Manual Reset procedure for waste ink tank full error in Canon Smartbase MP730 printers:

• Hit the “menu”: Key
• Hit “Copy” Key
• Hit “#” Key
• Scroll thru the menu headings until you come to “Test Mode” - 12th heading
• Hit the “3′ button- this will bring up Eeprom Clear
• Hit “0′ button
• Hit the “Stop” button

Good luck!

Hi,
#334 is an eprom error, try turning it on and off to reset it, if it doesn't work there might be a problem with the main logic board.