Cover door for document feeder not closed

PDF]HP Officejet Pro X476 and X576 MFP Series ... - Parts Now

www.partsnow.com/.../Officejet%20Pro%20X476%20X5...

Parts Now LLCFigure 2-6 Printer status report-determining genuine HP ink usage . ..... Thesecartridges are linked by flow connections to the rest of the printbar and supply the ink..... The left door can be opened for jam clearance and has a hall effect .... The document feeder will not function when the document feeder cover is open.

db:: 4.32::Printer door will not close after printing 8p - Hivmr

www.hivmr.com/db/8p83f78d97fk8c883x9p9za3mf993scf

On the 50.8 error message, if power cycling doesn't fix the issue you may need to ...Opened printer cartridge access door and removed paper. ... HP Officejet Pro L7580, the latch to the ink cartidges broke, so the door won't close. ... Can not close the printer door on my HP B210a, after cartridge replacement need help?

Re: Do u need Help? -HP All-in-One's(Officejet,Psc's)

www.fixyourownprinter.com/posts/28357
Also, when reinstalling the HP it does print a test page, but will not print from ...Encoder Strip has been cleaned with water (had some ink residue). ..... when opening the door the cartridge does not move to the middle so i can remove it, clean it ...... Iopened the covering part of the scanner (with the glass) nad cleaned all the ...

HP Officejet 6210- repeated ' FixYourOwnPrinter

Try holding the table top lid down gently while you feed it into the document feeder. It may be that it is not reading the top as closed to defer to the feeder.

Leading cause of paper jams is debris/foreign objects that accidentally fell into the paper feed area. Please follow steps below to fix the problem:

1. Remove the sheets of paper from the feeder.

2. Grab a flashlight and look inside the feeder for any debris or foreign objects.

3. If you're willing and physically able, you may also turn the printer over. Any debris should just freely roll out from the feeder.

4. If feeder is clear, place the printer back on the table, open the printer cover and remove the cartridges.

5. Check the cartridge area for any obstructions/debris in the cartridge carrier's path or the paper path.

6. If cartridge area is clear, close the cover.

7. Re-brick your printer. Pull out the power supply, black box where the power cord is plugged in at the back of the printer, and put it back after 30 seconds.

8. When the printer turns on, reinsert the cartridges and load some paper. Try to print a document again to verify that the problem is fixed.

Open ADF feeder cover find out the sensor location observe is there any breakage, if not insert a peace of paper in sensor, see the messiage..if its remain same it might be a problem with sensor, formatter or cable faulty.. if its gone.. used your brain...close it..best of luck..

problem with the feeder sensor >>top at the arrow

Hi nigel_lester,

This error message "Document in ADF" that you are getting means that you need to remove foreign object from the Automatic Document Feeder (ADF). Kindly follow the procedure below in clearing document jams:

Document jams in the ADF (Document Tray)

1. First, press Stop/Reset.
2. If a multi-page document is loaded, remove any documents other than the jammed page from the ADF. 3. Then, open the Feeder Cover.
4. From under the roller to the Feeder Cover side, remove the jammed page.
5. If a document is not jammed, check the document feed area if there's foreign material. If there's any, carefully remove it.
6. Close the Feeder Cover.

NOTE:

• If documents remain in the ADF after pressing during scanning, [Document in ADF] will appear on the LCD. Press so that the remaining document is automatically fed out.

• When rescanning the document after clearing the error, rescan it from the first page.

Document jams in the ADF (inner side)

1. Press Stop/Reset.
2. If a multi-page document is loaded, remove any documents other than the jammed page from the ADF, then open the Feeder Cover.
3. Raise the paper release lever (A) then remove the jammed page from under the roller to the Feeder Cover side.
4. Open the Document Cover and pull out the document from the inner side.
5. Close the Document Cover.
6. Close the Feeder Cover.

Note: When rescanning the document after clearing the error, rescan it from the first page.

Hope it helps.

Thank you for using Fixya.

Try :

• How do I reattach the document cover?
• How do I load the paper?

Does this machine have an ADF ( document feeder) on it? If so, check the connect cable from the document feeder to the machine. Also check the connectors from the scanner PWB to the document driver PWB. ( these are the 2 boards that do the communicating , the machine and the document feeder). If this machine does not have a ADF the check the side covers/ doors and make sure that they are closed securely.

better u disconect ur document feeder wire connection. and than try that.

There is most likely a very small piece of paper in the document feeder.
What you can do is take a minella folder or some card stock, open the document feeder cover and shove the folder or card stock through the feeder to dislodge whatever is stuck in there.
The document sensor itself may be knocked out of position.
It can't be the copy paper path since you can print.