Whirlpool MH3184XP Microwave Oven Logo

Related Topics:

Posted on Feb 07, 2018

Whirlpool Hood Combination model MH3184XP keeps beeping and running the power setting down in sequence from 10 to 1 then starts over again. Cannot get it to stop unless you unplug it. Once you plug it back in you can get it to work 1 time then it starts it's beeping with the power count down.

2 Related Answers

Anonymous

  • 2 Answers
  • Posted on Jan 20, 2009

SOURCE: whirlpool microwavewave hood comination mh3184xp

There are 3 fuses in that microwave. I had a similar issue. The one that I had to replace was the little ceramic fuse that is in line after the big fuse which is connected to the main line.
I couldn't find the ceramic fuse but I replaced it was a glass one about a year ago and it has been working since then. The fuse if located on the right front panel.

Ad

Anonymous

  • 1 Answer
  • Posted on Dec 13, 2009

SOURCE: Whirlpool Microwave Hood Combination MH3184XPS-0

Ours just started doing this exact same thing this past Friday - 12/11/09. What's going on? The cook power just starts beeping all by itself and going from 10 down to 1 over and over again. It may stop momentarily, but then starts again within a minute or so - it's constant until we unplug it. We plug it back in and within a few minutes it starts doing it again. What gives?

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Whirlpool mircowave model MH3184XP the display reads F2


There is a problem with the control pad. The membrane, or surface, of the pad may be broken or damaged somewhere, resulting in the F2 error code. This is common for Whirlpool microwaves.


Press "Stop/Cancel" twice and select a new cook program. Press "Start" to begin.

If the error code persists, press "Stop/Cancel" again and unplug the microwave. Wait several minutes and plug it in. If the F2 code appears again, it requires repair.


Replacement membranes can be found online


http://www.appliancepartspros.com/whirlpool-panel-asy-control-8205376-ap3775860.html


but the internals of a microwave are dangerous, having high voltages even when unplugged. With the cost of parts and labour from a service tech, you may be best buying a new oven.
0helpful
1answer

Powers off immediately after starting

My immediate reaction would be to cut your losses and buy a new unit as sooner or later you will run into a part that is no longer available.
0helpful
1answer

My microwave is about 1 and a half years old and it feels like it is not heating things as well as it used to. What could be the problem?

If you measure the temperature of 1/2 litre of tap water. Place it in the oven and heat on full power for 1 minute.
Take it out and measure the temperature again. If the difference is 10 degrees Celcius or more difference the magnetron is healthy if not, it is low emmission and must be treated as a lower output machine.
0helpful
1answer

Whirlpool MH3184XP Microwave Turns On, Heats, but sounds like fans not working. 4 years old, fans worked fine until they seem not as loud anymore. The magnetron is working fine as it heats (did the 1 cup...

Suggest you pull the plug out, remove outer cover and place a cup of water into the micro. Set power to minimum then switch on and take note if the fan works or not. If not, switch off immediately and have it replaced(magnatron will burn out if left to run without fan.)
0helpful
1answer

Hello, I have the whirlpool microwave oven, Model ...

logic board needs replacement if it cannot be reset.
0helpful
1answer

Whirlpool Microwave Hood Combination MH3184XPS-0 (October 2004), for no reason at all, this morning keeps beeping and running the power setting down from 10 to 1, and just keeps doing it in rapid sequence....

Ours just started doing this exact same thing this past Friday - 12/11/09. What's going on? The cook power just starts beeping all by itself and going from 10 down to 1 over and over again. It may stop momentarily, but then starts again within a minute or so - it's constant until we unplug it. We plug it back in and within a few minutes it starts doing it again. What gives?
1helpful
3answers

Whirlpool microwavewave hood comination mh3184xp

My Whirlpool MH3184xps is shooting a spark when in use with the rack. When the rack is removed the oven works fine. I am guessing that some of the coating on the rack has cracked and peeled and is exposing some aluminum. Has anyone else had this problem?
0helpful
3answers

Whirlpool mh3184xp- microwave and lights turn on by themselves

inside microwave oven may be wiring damage check wiring and contorl circuit,
0helpful
1answer

Whirlpool Microwave Model MH3184XP

This is most often caused by a bad magnetron "scrambling" the controller, a bad connection on the controller, or a controller failure. Try to use the "timer" function of the oven. Make it count down without cooking for about a minute. If it works, then it's more likely to be a bad magnetron. If it still fails, it's probably a problem on the controller. We repair these nationwide by mail for $39.95 in most cases. For more information see our listing here on FixYa: http://tinyurl.com/yzjozk
Not finding what you are looking for?

125 views

Ask a Question

Usually answered in minutes!

Top Whirlpool Microwave Ovens Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Cindy Wells

Level 3 Expert

6688 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Whirlpool Microwave Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...