How do i change the system settings? i cant find where to go in and get it on my computer. i need to change the name and the # of wireless out puts. :)

Are you trying to secure the wireless network?
For this you will need to access the router setup page and change the settings manually.
See how to secure wireless network.

If you are not able to save the settings then I will suggest you to upgrade the firmware of your router. The reset the Linksys router and reconfigure it manually.
Create a new wireless network. Change the name of the wireless network that you never used before.
Then try to connect to the new wireless network.
See How to reset Linksys router.
See Linksys router setup

if theres 2 account holders delet your account going under that person name then rest your box then put your name back in reset your computer then plug router in.

Just log in your router set up page and configure those PC,s.The PC,s are going to have different IP,s.No PC<s will have the same IP.In the router set up select DHCP and state the IP of each PC.Post your router model will give more info. to help you.

If you need more help come back.Post / thumbs / testimonial are welcome!

to make your router private u will have to get acces to ur router firs if u cant just reset the router from the back the log to the internet and if u cant conect type this192.168.1.101 the brand name of the router appear then enter the user name and pasword if u cant type ADMIN in the user then press enter then go to settings and chose WEP share key and type your password recomment to use a strong password ok then click save. also create a user name while u in thre ok. that will reset the router after that go to my network conection right click on ur wireless router name and go to propertis then chose the WEP share key and type the password then ok. that will set ur router privated ok. good luck

when you change the wireless security on the router , it is recommended tht you will change the wireless network name also ( SSID ). Because when you try to connect to the wireless network on the computer, your computer will try to connect to the same old network name with the old wireless security settings. To avoid this you can change the wireless network name. WPA is supported by windows XP SP2 and above operating system.
If the operating system on your computer WINDOWS XP SP1 and if you are trying to connect using the windows utility then you would not be able to connect to the network .

Click Here for more information about the routers and networking

open wireless connections and delete the network settings completely then set it up again, you have manually disconnected from the network at some stage which is why it doesn't auto connect each time. To delete the settings you need to go into advanced settings, as you dont say which windows version you have i cant give specific instructions

Manual for WBR14-G2 router [6.2 MB] in pdf format:
http://www.smc.com/files/AG/MN_SMCWBR14-G2.pdf

Keeping others from connecting to your router:
1. Have an "wired only" router login access or for this router "change and disable your SSID". This way you avoid that others can login to
to the router changing your settings: See page 48 of the manual.
1.1 Wireless Network Name (SSID): change the default name SMC
to "any private name" ( and remember for later login )
1.2 Broadcast Wireless Network Name: change from default ENABLE
to DISABLE .

2. Make a secure wireless encryption key for your connection:
see page 87.
2.1 For most secure key select WPA / WPA2 only and SAVE SETTINGS .
2.2 See page 91 for entering and saving your secure key: the password
that must be entered to get access to the router.

how many wireless computers do you have?
is it a dekstop or laptop?
if desktop have you installed a wireless adapter? if laptop, is it using a built-in wireless adapter, have you enabled the wireless adapter or have you installed a wireless adapter?
-------

please make sure first that the wireless adapters are installed properly or enabled on your computers, if everythings OK.

-------

access the setup page of your router and change the wireless settings of it.

how to access the ui
- open the internet explorer
- on the address bar type in 192.168.1.1 hit enter
- enter admin under password, leave it empty for the username and click ok
- click the wireless tab
- set the wireless mode to mix, change the wireless network name or ssid with any preferred name you want to use, make sure to enabled the ssid broadcast and then click save settings.
- after that, under wireless tab, there are sub tabs, click wireless security
- set wireless security to WPA-PERSONAL, and under passphrase, enter your desired password for wireless connection, take note of it and please be reminded that its case sensitive.
- click save settings.
----------------------------
for your wireless computers, if adapters enabled and working fine, on the system tray you should have an icon for the wireless connection, doubles click on it and it will pop for the wireless connection window wherein you can see the name that you set on your router, all you have to do is select the name click on connect and it should ask you enter a password, enter the passphrase you set on the router and click connect. then check if you can go online, if yes do the same thing with other computers.

Have a great day ahead.

You can see the SSID name from one of your wireless computer that is already connected to the wireless network. Just point your name over the wireless little computer icon down at bottom right hand by the time. It will say there "Wireless Network Connection, Connected to "name of the network". That "name of the network" is the wireless signal name like "Linksys" or whatever name you gave to your network when you setup the router. That's the SSID name as well. Wireless Network Name = SSID.

There is a possibility that the user name and password that you are using is not used for the wireless connection of the network. If you have WPA enabled on your router, you need a password with a minimum number of 8 characters. If you enabled WEP on the router, it may need 10 or 26 characters depending on what type of encryption is enabled on the router.

You can check that using the Web interface of the router. Try these steps:

1. Connect a computer to the router wired then restart the computer.
2. Launch an internet browser and type in http://192.168.0.1 or if you changed the IP, use the changed address.
3. If it asks for a user name and password, set admin as the user name and password as the router password. If you have changed the password, use the new password.
4. Click on the wireless and check the security type. Make sure that the Mac filter is disabled and there you can find the network key set on your computer.
5. You can then use that key to connect your wireless computer