Will a HRMC 8 Program to a dvd/vcr combo by Toshiba?

Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the site linked here. It has set-up code list & set-up procedure to many popular brand remote controls. See it in "Mosaic" or "Magazine" view. It will make surf easier.
http://electrohelponline.blogspot.com/
http://remotesearch.blogspot.com/

Hello
Here are the proceedings to setup your remote with other devices.

The One For All 3 Device Universal Remote Control is preprogrammed at

the factory to operate an RCA TV, a Toshiba DVD player, and a Motorola

cable box.To control devices other than the default brands,perform the following
steps; otherwise skip this section:

[1] Turn on a desired device (e.g.,VCR or DVD player) and, if

applicable, insert media (e.g., cassette or disc).

NOTE: Please read steps 2 through 4 completely before proceeding.

Highlight or write down the codes and device you wish to program
before starting step 2.

[2] On the remote control,press a device key once (i.e., DVD/VCR,

CBL/SAT,or TV).

NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo,

or TV/VCR/DVD Player Combo press DVD/VCR once.After programming

a VCR Combo device, you will be able to control channel selection,

volume, and VCR functions.

NOTE: To program control of a DVD Player,DVD Player/VCR

Combo, or TV/DVD Player Combo, press DVD/VCR once.After programming

a DVD Combo device, you will be able to control channel

selection, volume, and DVD functions.

NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR)
Combo, Satellite Receiver, or a

Satellite Receiver/PVR (or DVR)
Combo, press CBL/SAT once.

[3] Press and hold SET until the LED (red light) blinks twice,
then release SET.

[4] Use the Manufacturer's Codes (starting on page 18) to

locate the type of device and brand name and then enter

the first four-digit code for your device. If performed correctly,

the LED will blink twice.

NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter
the same code again.

[5] Aim the remote control at the device and press POWER

once.The device should turn off. If it does not, repeat

steps 2 through 5, trying each code for your brand until

you find one that works. If it still doesn't work, try

Searching For Your Code on next page.
NOTE: If the device does not have a POWER key, press PLAY.
Repeat steps 1 through 5 for each device you want to control
OK

Hello
Codes for RCA tv with Hughes remote are:

160 161 156 165 065 070 004 023 024
056 074 081 152 167 145
Code Entry

Use the REMOTE pane under the System Setup menu tab to program your

HRMC-11, HRMC-12, or HRMC-13 remote control to operate your TV, VCR,

SAT, AUX device, or DVD (HRMC-11 and HRMC-12 only). The AUX menu

button can be used to control a CATV box or other type of device. Use the menu

buttons to choose the desired type of device and display a brand name menu list
from which you can select the manufacturer of your device.

Code scanning

To use the Code Scanning method:

1. Repeatedly tap the top part of the CHANNEL (CH) button.

2. Continue to step through the codes until the component turns off, indicating

you have found the correct component code. If you accidentally pass a code

that responds or realize you may not have been aiming the remote control at

the component, tap the lower part of the CHANNEL (CH) button to step

backward through the codes.

3. Press the remote control POWER button to verify the proper code by

turning the device on and off.
4. Press the device button (in this example, TV) again to lock in the code.
OK

Configuring codes:
1.Turn on a desired device (VCR or DVD player)

2. On the remote control, press a device key once (i.e., DVD/VCR,
CBL/SAT or TV).

NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo, or TV/VCR/DVD Player Combo press DVD/VCR once. After programming a VCR Combo device, you will be able to control channel selection,volume, and VCR functions.

To program control of a DVD Player,DVD Player/VCR
Combo, or TV/DVD Player Combo, press DVD/VCR once. After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions.

To program control of a Cable Box, Cable Box/PVR (or DVR)
Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)
Combo, press CBL/SAT once.

3. Press and hold SET until the LED (red light) blinks twice,
then release SET.

4. Use the Manufacturer’s Codes to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly,
the LED will blink twice.

5. Aim the remote control at the device and press POWER once. The device should turn off. If it does not, repeat steps 2 to 5, trying each code for your brand until you find one that works. If it still doesn’t work, try Searching For Your Code on next page

Auto Code Scan:
1.On the remote control, press TV once.

2. Press and hold SET until the LED (red light) blinks twice, then release SET.

3. Enter 9 - 9 - 1.The LED will blink twice.

4. Aim the remote control at the TV and slowly press POWER button.Stop when the TV turns off

5. To lock in the code, press and release SET.The LED will
blink twice.

6. To search for the codes of your other devices, repeat steps
1 to 5, but substitute the appropriate device key for the device you are searching for.


Thanx

from the book: this is for the HRMC-5 may be the same.
Code Scan if you don't know the code.

Keep remote aimed at the device you want to control. during the programing, the device will send out a "power" command for the device being programmed.

While holding down the device key(i.e., TV) that you are programming, press the "Mute key for one full second. then release the keys. the device key should light up and stay lit. if not, repeat the process.

repeatidly tap the channel up key to step through the codes, sending out the "power command". may take some time, many codes. when device shuts off, you have found the code. If you inadvertantly went past the code, that responded, you can press the channel down key to go back. press the "power key to verify you havent missed the code. In order to lock in the code, press the device key again. the remote will remember the code till you re program it.

dont have codes for programing HRMC-5 (11), I HAVE A SYMPHONIC tv

I have a HRMC-8 remote. Cant find the manual and need to program for a different TV?

Hold down Select and Mute until the tv light flashes. The enter the code and press Select.

http://www.directv.com/learn/pdf/System_Manuals/Hughes/HNS_SD_HBH.pdf
remote programming instrutions start on page 49 of the PDF file and give step by step instructions for programming your remote

The manual is at
http://www.directv.com/learn/pdf/System_Manuals/DIRECTV/DIRECTV_D11.pdf