Stop answering on 10th ring

Has the answering system been turned off? Check the base, there is an Answer On button with a LED indicator. If the light is off, press the Answer On button. From the handset when the phone is in Standby, press Menu/OK and navigate to Answering Device using the Up/Down arrows. Press Menu/OK to enter the Answering Device menu. Use the arrows to go to the Answer On and press Menu/OK. Then press Off to exit the menu system. If you are calling into the phone, you can turn on the answering system. Let the phone ring 15 times followed by a long beep, then enter your remote code within 10 seconds. Either hang up or do any remote operations. Note: pressing 0 will turn off the answering system.

When you set up the ring count, the maximum rings before the system picks up is 7. In Toll Saver, the phone rings twice if there are new messages and 5 times otherwise before you hear the greeting. Even when the recording space is full, your greeting or a pre-recorded "mailbox full" statement will play. (Note: some of these systems allow for a greeting to play without saving any messages. This is controlled by the "recording time" option.)

I hope this helps. See the manual for the KX-TG4021 on the support page: https://shop.panasonic.com/support-only/KX-TG4021N.html. The current link to the manual is https://ftp.panasonic.com/telephone/om/kx-tg4011_mul_om.pdf . Start on page 27 for the Answering Device information.

Cindy Wells

After setting the number of rings, press PLAY/STOP to save the setting and exit the menu. Full details are on page 2 of the manual.

Press and hold [SET UP] until the system announces "Number of rings is..." Press and release [ANNC/SKIP] or [MEMO/REPEAT] until the system announces the desired number of rings. Press [PLAY/STOP] to exit. Full details are on page 2 of the manual.

Press and hold [SET UP] until the system announces "Number of rings is..." Press and release [ANNC/SKIP] or [MEMO/REPEAT] until the system announces the desired number of rings. Press [PLAY/STOP] to exit. Full details are on page 2 of the manual.

Issue When the all-in-one product is sharing a phone line with voice calls, some calls are interrupted by fax tones. Follow the steps below to solve the problem.Step one: Check the Rings to Answer setting If Auto Answer is enabled, the HP fax product will answer the phone line when the number of rings reaches the number of rings specified in the Rings-to-Answer setting. When voice calls will be received on the same phone line as faxes, set to rings-to-answer to 6. If you do not want the fax to answer automatically, either turn off Auto Answer from the front panel and receive faxes manually (this may result in lost faxes) or subscribe to a distinctive ring service from the phone company (if available). Refer to the Answering faxes manually section below to learn how to answer faxes manually or refer to the Using distinctive ringing section below for more information about using distinctive ringing. The Rings-to-answer setting for the HP Officejet 500 and 600 series products can only be checked or set using the all-in-one software on the computer. The Rings-to-answer setting for the HP Officejet 500 and 600 series products can only be checked or set using the all-in-one software on the computer. Follow the steps below to check or change the setting for all models except the HP Officejet 500 and 600 series:

1. Depending on the model, press either Menu , Setup , or Fax Setup repeatedly until Basic Fax Setup appears in the display.
2. Press Enter (or Start or OK ).
3. Press the right arrow button repeatedly until Rings to Answer is displayed, and then press Enter .
4. The number of rings before the HP fax product answers will be displayed.
   • The setting is correct if it is 6. Press Cancel or Stop (Stop Fax) to exit the menu.
   • If the number is not 6, press the right arrow button until 6 appears in the display and then press Enter (or Start or OK ).

Press and hold the STOP/SET button for two seconds. After the time and day you can change the rings to answer.

Full details are in the "Changing the Settings" section in the third column of the manual. If you need a manual, you can download one at
http://www.home-electronics.net/USER-GUIDES/29888_DOM_EN_AN_IB.pdf

Here is the manual
http://ec1.images-amazon.com/media/i3d/01/A/man-migrate/MANUAL000017395.pdf

Press and hold SET UP for two seconds,

press annc/skip or memo/repeat until the number of rings you want is announced, and then press play/stop to exit.

Short answer: You download the Operational Guide from Pulsar:

http://www.pulsarwatches.com/home2.asp#FAQ (look for N944 which is PGC series).

Longer answer: It is baffling to do this without the manual. You put the watch in -0- mode (crown fully in), pull the crown out to first stop, then us the A and B buttons to zero the 1/10th and second hands, then pull the crown out to second stop, then use the A and B buttons to zero the minute and hour hands. Then, you put the watch in "Time" mode (crown fully in), pull the crown out to the second position, and use the A and B buttons to set the time. You have no functioning second hand except for the stopwatch - in Time mode it acts as the calendar hand.

Press and hold STOP/SET button for two seconds to access the set-up menu. Press STOP/SET to continue. Press STOP/SET over and over until the Machine says "Rings to Answer". To set the rings to answer just press NEXT or PREVIOUS to select how many rings you would like. Toll Saver option answers after 5 rings unless you already have a message, in that case it will answer after 2 rings. After you hear the option you like, Press STOP/SET button to store it. Now just press STOP/SET over and over until you get to the end of options, it should beep when you get there. Once you get to the end the machine will announce all the settings for review.