Ip address,subnet mask, gateway - Microsoft Xbox 360 Arcade

subnet mask is usually 255.255.255.000, or something like that. If you not know what it is, no use trying to set it up. Most devices do set this up after they know what the ip address is. Look what the router or your hub makes for other devices. The gateway (address) is the ip address your provider gave you to connect to.

Connect your computer wired or wirelessly to your router.
in windows based comp
open command prompt
type -- ipcofig
you will get your answer

IP Address: 245.36.4.25
Subnet Mask: 255.255.0.0
Gateway: 245.36.0.1

If fail suggest to set iRC2620N to DHCP so that your DHCP server or router to assign a TCP/IP address.

http://www.usa.canon.com/cusa/support/office/color_imagerunner_copiers/color_imagerunner_c2620_c3200_c3220/color_imagerunner_c2620_c3220

When configuring an address for the printer, the IP configuration might look like (just an example):

IP Address - 192.168.1.2

Subnet Mask - 255.255.255.0

Default Gateway - 192.168.1.1

It's important to note that even though you are not using any IP addresses in the default range for DHCP, the Subnet Mask and Default Gateway addresses will be THE SAME.

If you have another device on your network that will be assign a fixed address, you would use for example:

IP Address - 192.168.1.3

Subnet Mask - 255.255.255.0

Default Gateway - 192.168.1.1

For any other devices, just increment the IP address by one, 192.168.1.4, 192.168.1.5, etc and use the same Subnet Mask and Default Gateway.
(see the owners manual or site for steps on configuraing the printer TCP/IP information). This should take care of any conflicts.

Hello!

I will just illustrate on how to configure or to set the correct IP addressing;

Assuming that we will manually put IP address on each computer:

PC1:

IP Address: 192.168.1.13
Subnet mask: 255.255.255.0
Default gateway: 192.168.1.1

Preffered DNS server: 192.168.1.1

***note that 192.168.1.1 is the IP Address that your ISP gives to you, so on the other computer (see below)


PC2:

IP Address: 192.168.1.18
Subnet mask: 255.255.255.0
Default gateway: 192.168.1.1

Preffered DNS server: 192.168.1.1

Hope I was able to help.

First find out the IP address , Subnet mask,and Gateway addresses of your ISP ( Internet Service Provider ). According to above addresses, you have to complete the network settings of your printer by mentioning the different IP address .

To find out the above mentioned addresses, first open the control panel -> network connections -> local area connction -> properties -> Internet Protocol Version 4(TCP/IPV4) OR Internet Protocol Version 6 (TCP/IPV6)according to your ISP -> Properties

By the systematic selection as mentioned above you will get the IP address, subnet mask and Gateway addresses.

Suppose your IP address is 192.168.0.10 , the gateway may be 192.168.0.1 Or any number. And the subnet mask may be XYY.XYY.XYY.0.

According to your ISP addresses you have to complete the network settings of your printer. First press the additional functions -> system settings -> network settings -> TCP/IP settings -> fill up the addresses as follows.

IP address : 192.168.0.16 OR any number .

subnet mask : XYY.XYY.XYY.0.

Gateway : 192.168.0.1

Hurray ! the problem about your network connection with the printer to your computer will be automatically solved.

I had a similiar problem; check your PC settings and find out your IP address, subnet mask, default gateway and DNS settings and write them down. (from "run", type "cmd", then in the window type "ipconfig /all")
if your IP address is (for example) 192.168.1.1 mask 255.255.255.0 and gateway is 192.168.1.254, go to your Wii settings and change the internet settings to NO DHCP, give the Wii an address of 192.168.1.10 with the same subnet mask, default gateway and DNS server setting as your PC. Remember the FIRST 3 numbers of the IP address must be the same and the last one DIFFERENT.

well!! I have an answer for you.your comp is loosing the IP address. goto start - programmes - accessories - dos prompt. type ipconfig.you`ll get ip address,subnet mask,default gateway.copy it. goto network and sharing center,click on view status,goto propertiesand double click on internet protocol(tcp/ip) or IPv4.type in the IP address,subnet mask,default gateway.in DNS server address type the default gateway in primary DNS and in secondary 4.2.2.2. your connection won`t drop after this.

Hello Sir,

all computers on the same physical subnet need to have ip addresses in common
meaning the first three numbers in aaa.bbb.ccc.ddd are the same and are different only in the ddd portion.
In addition, the subnet mask must be alike or ensure that some ip addresses are not excluded
Typical subnet mask is 255.255.255.0 or sometime 255.255.254.0
Usually, there's a gatway address; a target which is used to send packets out
of this machine and hopefully towards the other machine.

For all machines, use the Run->cmd and enteripconfig /allYou should have similar results on all machines, so look for major differences eg: gateway on one is 0.0.0.0 or not shown while other have non-zeros,
or ip address on one start 169.254 another starts with 192.168

The 169.254.y.z addresses are pecuilar

ms article comments on auto-config:
example : IP-address assigned via Auto-IP-Configuration :
Windows IP Configuration
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Autoconfiguration IP Address.. . . : 169.254.4.69
Subnet Mask . . . . . . . . . . . . . .: 255.255.0.0
Default Gateway . . . . . . . . . . . . :



Thanks
Cheers!!!!!!
Good luck

Yes, the xp machine connects to the net. DHCP is not enabled. The ipconfig/all command brings up the correct static ip address, subnet mask, and default gateway. But it does also say under the ip configuration that ip routing is not enabled. I did have the 2000 machine connected when I first set up the router yesterday, but I booted up my laptop to try to set up a wireless connection, and then I had to reinstall the entire router set-up.