I have a Panasonic KX-T7731 business phone system and I am trying to do the following" Program specific phones to be alerted with a tone for phone-to-phone intercom calls but to NOT be alerted when the doorphone rings. I have already programmed the phones to disable call waiting, but it does nothing. Is there just a way to program certain phones to NOT HAVE the doorphone ring at that extention??? Help!

try and use (the star icon and 72 or 73)I think that is the code for telephone companies__one turns it on and one turns it off

Panasonic analog phones plug into analog KSU's and have extension numbers beginning with 101. In additon, you can dial 0 to reach the phone programmed as Operator, and it's usually extension 101.

With the intercom dial tone (press INTERCOM or pick up the handset or press SP PHONE) you can start dialing codes defined in your number plan. You can also program left side buttons to monitor are directly select other extensions or dial codes to page all idle speakers in a 77xx phone.

Note this is specific to TA series systems, but the operation is similar in all Panasonic models.

Carl

You have a 7731 phone. The phone system could be any one of 18 Panasonic cabinets, but probably a TA series. Voice mail could be a BV, TVx box, or central office based. If CO based, an 824 will listen for the stutter dial tone and light the MW light on a phone. There are instructions to make that work.

So, try editing your question to give a bit more information and it makes it easier to give you an answer.

Carl

Not possible. A Panasonic Analog PITS phone has only one ring sound and all CO rings match.
The TD series and 74xx phones were the first phones to have 8 ring tones. The TDA series has 30 different tones. Prices are fairly competitive for upgrading.

From that phone without picking up the handset, press PROGRAM button #1 and dial 01 STORE.

Carl

What happens when you dial "9" into the intercom dial tone? Is that the line you wnat to auto select?

A lot depends on the system your phone is connected with. In a TA series on an idle phone, press PROGRAM 11 for no preference (what you have) 12 for Idle line (what you get when you dial 9) or 13 and a number from 1 to however many lines you have to select a specific line.
Those commands are followed by the STORE button and PROGRAM to end the programming.

Carl

There are a few types of phone sytems that work with the kxt 7731. these instructions should handle most of them.
Changing the time on a Panasonic KX-TA624 system must be done from extension # 101 using a display phone. All others can use any display set. 1.- Press the "PROGRAM" button on the face of the phone
2.- Enter programming mode by pressing "STAR" - "POUND" - "1234" (default password = 1234)
3.- Enter program # 000 4.- Press "SPEAKER" button 5.- Press "FORWARD/DND" button to change to the hour selection 6.- Press "TRANSFER" button and enter the hour 7.- Press "FORWARD/DND" button to change to the minutes parameter 8.- Press "TRANSFER" button and enter the minutes 9.- Press "FORWARD/DND" button to change to the AM/PM parameter 10 Press "MUTE" button to select AM or PM 11.- Press "STORE" button (listen for 1 tone if procedure was executed correctly / 3 tones if procedure failed) 12.- Press "HOLD" button 13.- Press the "PROGRAM" button on the face of the phone

Not sure what you mean by "off". What is it doing and what do you want it to do specifically? Is it sending a tone or alert when an extention phone is called via intercom?

REFER THE MANUAL AT http://www2.panasonic.com/consumer-electronics/support/Phones-Fax/Business-Home-Systems/System-Phones/Advanced-Hybrid-Phones/model.KX-T7731

On that phone, press PROGRAM the button and dial 01 STORE.

Press program again to exit programming.

It's not likely you'll be needing the Group Log In/Out button.

Carl