I have a g1100b. having problems setting the alarm. I keep setting it to 0600 but the alarm consistently goes off at 1300 daily. any ideas of how to set the alarm correctly?

Set multiple alarms. If any alarm is active,(picture of alarm hear) appears in time display A. Press MODE repeatedly until ALARM appears, followed by ALM1. Press STOP/RESET to select Alarm to set. B. Press SET/RECALL to set alarm. HOURS digits will flash. Press +/- to change HOURS. C. Press NEXT and +/- to set MINUTES, AM or PM (if primary time display is in 12-hour format), DAILY, WKDAYS, WKENDS, or day of the week (weekly alarm). D. Press DONE to exit. E. Press +/- to set different Alarm. Set as above. F. In Alarm mode, press START/SPLIT to turn Alarm ON or OFF. TIP: Alarms apply to selected Time Zone of watch display. Backup Alarm sounds after 5 minutes if no button is pressed. Turning off any Alarm or backup will not affect other alarms. http://assets.timex.com/user_guides/W191_M131/W191_M131_NA_EN.pdf

go here to download instructions > http://www.citizenwatch.com/en-uk/support/setting-instructions/

TURNING OFF A TIMEX IRONMAN (the wr100m is the one I made this work on) ALARM: hold "set" to set each alarm to "on," not "hide." exit. flip through the modes until each alarm shows. don't hit "set," hit "start" or "stop." it should then switch from showing as daily or whatever to showing as OFF! good luck. so, UNHIDE, SHOW ALARM, DON'T SET, STOP -> OFF.

casio gshock...Setting the TimeG-Shock watches feature a digital display that is set using the function buttons on the outside of the watch face. To set the time, press and hold the the upper left ...">casio gshock...Setting the TimeG-Shock watches feature a digital display that is set using the function buttons on the outside of the watch face. ...

Hi trapmanjohn,

Man what an aggravating problem! Try this procedure.

1. To turn the daily alarm and time signal on and off:

2. In the Alarm mode, press "B" , upper right button, to cycle throught the on and off settings as follows:

Alarm on Indicator/Hourly Time Signal On Indicator
a. }}}} with Bell = Both alarms on
b. Display Blank = Both alarms OFF
c. }}}} = Daily alarm on only
d. Bell = Hourly time signal on only

The Alarm ( }}}} ) indicator flashes while the alarm is sounding.

The Alarm ( }}}} ) indicator and hourly time signal on BELL indicator are displayed in all modes.

To Test The Alarm: In Alarm Mode, hold down the "B" to sound the alarm.

Your Module number is #3171. Down an Operation Guide for the 3171 from here for more clarity:
http://ftp.casio.co.jp/pub/world_manual/wat/en/qw3171.pdf

This should help you with nuisance...Good luck.

Regards, Bill

I looked at the Seiko web site and found only one of the listed watches was described as a "chronometer" and that one did not have a daily alarm.

To review the instructions, go to "seiko.com", then "support" and click on "instruction booklets".

There is a diagram showing where the information is that should be entered to give the instructions you need.


Alternatively, below the diagram is a list of watches which you may be able to find your watch .

To set the alarm, press the lower left button until "AL" appears.
Press and hold the center right button until the time digits flash.

Use top or bottom right buttons to set the time.

Press the center right when you have done setting the time.

Press the center left button to start or cancel the alarm.

The alarm will sound for 30 seconds; Press any button to stop.

Te alarm will repeat daily until it is turned off.

how do I turn off the hourly setting

what you have to do is
1. press the mode button until you get to the setting that has "AL" at the bottom right.
2. then you press the "receive" button to switch between the four alarms.
3. as you are going through each alarm time, you need to look in the circle at the top right. When you are going through the alarm times, if there is a mark next to "ALM", you need to press the "time memo" button so that the mark next to "ALM" is no longer there.
4. repeat step fout for all of the alarms, and the problem should be fixed.

Alarm Setting:

1st: Press the mode button to go to the alarm screen.

2nd: Press the adjust button for the time to flash

3rd: (For the Hourly Alarm) You can adjust the time here while it is flashing by pressing the start/stop button. Cycle through this until you have the time you want. The setting will have the P in the left side of the screen for PM (night time).

4th: (For the Daily Alarm) Do steps  1-3 once the time is flashing use the Mode button to cycle through to the date field of the watch. Once it is flashing you can use the Start/Stop Button to chose which date Month/Day, after chosing the month just press the Mode button once more to go to the day field.