My samsung C410 printer has an orange light that comes on while the printer is preparing to print. It then just stops and the orange light remains while the printer is unable to function. James

Orange LED indicated a Paper Jam.
Clear the jam as shown in page 76 of the manual attached.

http://downloadcenter.samsung.com/content/UM/201107/20110722094633890/EN/english.pdf

Dear Hamad
Pl. run the application SAMSUNG SMART PANEL or SAMSUNG EASY PRINTER MANAGER in pc. get a test print it will notice the exact error massage. You may also download the application from the link attached, by searching your model code.

Printer Support SAMSUNG India

Thanks.

orange light means that one of the printer cartridge is getting finished. The time it gets red that menas its totally empty.

Per Samsungs website:

When the toner cartridge is near the end of its life:

• White streaks or light printing occurs.
  

• The LED blinks red.
  

  
  

  
  

  If a paper jam occurs, the LED on the control panel lights orange. Find and remove the jammed paper.
  

  To resume printing after clearing paper jams, you must open and close the front cover.
  

  
  

  http://downloadcenter.samsung.com/content/UM/201011/20101130094714441/EN/User_Guide_en/english/start_here.htm
  
  

Do you have a new toner cartridge loaded? The red/orange light will blink when toner is low, even if everything else is working fine. Try printing out a test sheet and see what that tells you about your toner level. (Test sheep prints by holding the orange button down a second or two and releasing.)

Since I'm mainly printing drafts for my own use, I've just let the light blink while I eke out whatever I can from the remaining toner (occassionally removing the cartridge and shaking it -- being careful of clothes and surroundings -- to re-distribute the toner on the inside.

do you tried to tell an supplier?
Peace!

dear sir

1. it is problem paper miss feed
2. over temparature

clean thermostator.thermostator over dry toner
or cartridge assembling problem

OK lets try this

Also if you are using the Refillable ink cartilages stop they always cause major issues

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)Note: press 4 times for waste ink counter reset.

The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off

1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset

5) Turn off the printer.(it must be turn off)
then turn it on again.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one and to go on helping.
All The Best: Pineworks

1. Confirm that the printer is powered on and press the <Open> button (MP500) or manually pull open the paper output tray
   
   
2. Lift the scanning unit (printer cover) completely. (The print head will move to the replacement position.)
   
   
   NOTE: When the scanning unit (printer cover) is opened more than ten minutes, the print head moves to the right side. If this occurs, close the scanning unit (printer cover), and open it again.
   
   
3. Open the inner cover.
4. Unpack the ink tank and pull the orange tape off completely in the direction of the arrow and remove the film.
   
   
   
   Note: Tear the orange tape carefully along the dotted line. If the orange tape remains, printing problems may occur.
   
   
   
   
   <4> Tape is completely removed.
   
   
   <5> Tape remains.
   
   
5. Remove the orange protective cap located on the bottom of the ink tank by twisting as shown in the diagram.
   
   
   
   CAUTION: Do not touch the ink tank contact <6>. Doing so may cause printing problems. Do not squeeze the side of ink tanks as this may cause the ink to leak out. Do not reattach the protective cap once you have removed it.
   
   
6. Insert ink tanks into the print head.
   
   
   NOTE: Press the mark <PUSH> on the ink tank firmly until you hear a click.
   
   
   
   
   
   
   
7. Ensure that all the ink tanks are installed properly and the ink tank lamps light red.
   
   
   
   Note : MP500 shown.
   
   
   <7> The ink tanks are installed properly.
   
   
   <8> The ink tanks are not installed properly.
   
   
   NOTE: Click for Ink Tank Lamp indications.
   
   
   
8. Close the inner cover and the scanning unit (printer cover).
   
   
   CAUTION: When closing the scanning unit (printer cover), be careful not to jam fingers.
   
   
   Memo: The next printing begins, the print head cleaning will begin automatically.
   
   
   

Ink Tank Lamp indications
You can check the status of each ink tank according to the way its lamp flashes.
- On: The printer is ready to print.
- Slow flashing (at about three second interval): Ink is low. Prepare a new ink tank.
- Fast flashing (at about one second interval): Ink tank is empty, or the printer is not ready due to an error.
- Off: An error has occurred and the printer is not ready to print.