What is the correct button sequence etc to do a panel reset on a kitchenaid KUDE60HXSS1

This appears to be a Dishwasher rather than the category 'Cell Phones', so I moved it and Edited your Question.

Here is the answer for you.

How to reset a Kitchenaid dishwasher? Cycle Reset
If you just need to reset a cycle, simply press and hold the Cancel or Cancel-Drain button to reset the cycle and choose a new one.Apr. 20, 2018

The Reset Sequence for a KitchenAid Dishwasher ' Hunker

https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk00Z8bg7nFmtLavltrPr2TV9PXzEDw%3A1613419081369&ei=SdIqYLePFpGGsAXk04_4DA&q=kitchenaid+kuds02srss0+reset+button
..

Press High Temp Scrub and Dry Heat option buttons in quick succession one after the other for about 6 sec until all the lights come on. Then press Cancel button. This should reset the dishwasher. Press equivalent buttons on the panel if the actual ones above are not there.
Make sure the dishwasher detergent dispenser lid is shut and the dishwasher door is shut before you start the above reset sequence.

Hello & Welcome to FixYa

Flashing light is reset by pressing two buttons in sequence 3-4 times, to reset your dishwasher press these buttons in sequence:

High temp wash-heated dry-high temp wash-heated dry

Please get back to me if you have any other questions.

Kevin

Not sure what type of reset you are after. Is the dishwasher not responding to any panel switches.

Is the keypad locked, i.e., is the control lock light on? Then press Energy Saver Dry button for 4-5 secs.

Are some lights flashing and dishwasher will not start? Have you tried to turn mains power off and back on?

If you think the controller needs a reset, you could try this sequence of keys within 7-8 secs.
hi temp scrub/ energy saver dry/hi tempscrub/ energy saver dry/ hi temp scrub/ energy saver dry.

If the reset sequence has worked correctly, then all lights should light up. Press Cancel to exit from reset mode. I am assuming you have a users manual. If not then download from here.

Please rate the solution if it helps your problem otherwise post a comment

Hello & Welcome to FixYa

Flashing clean light is reset by pressing two buttons in sequence 3-4 times, to reset your kenmore press these buttons in sequence:

High temp wash-heated dry-high temp wash-heated dry

Please get back to me if you have any other questions.

Kevin

Hello & Welcome to FixYa

Flashing clean light is reset by pressing two buttons in sequence 3-4 times, to reset your kenmore press these buttons in sequence:

High temp wash-heated dry-high temp wash-heated dry

Please get back to me if you have any other questions.

Kevin

Hello & Welcome to FixYa

Flashing clean light is reset by pressing two buttons in sequence 3-4 times, to reset your kenmore press these buttons in sequence:

High temp wash-heated dry-high temp wash-heated dry

Please get back to me if you have any other questions.

Kevin

Probably a keypad gone bad. Try replacing the keypad.

There is a troubleshooting guide behind the foot kick panel. It gives a sequence to test for a bad keypad. You can try that sequence to be sure.

try the reset button sequence.. described in that other post about the clean light blinking.. that will reset the whole machine..

tpug

I found this post elsewhere. It seems to have worked for me: Our KitchenAid KUDP series dishwasher went into a mode where it would not start and would only respond to the cancel/drain button. The clean light would flash 7 times in a row, stop, and then repeat. I read that the 7 flashes indicates an error code and that the dishwasher has detected a problem in the heater element circuit. I tried to reset the error mode by turning off power for 15 minutes, however, that did not work.
We called for a repair. The service person found that the dishwasher was completely fine except that it had gone into an error mode. The technician reset the error mode and charge us $115.00.

The reset sequence used was reported to be the following:
1) Crack the door open.
2) Within 3 seconds press the following sequence - Hi Temp Scrub, Energy Saver Dry, Hi Temp Scrub, Energy Saver Dry
3) Close and latch the door
4) Press the cancel button (the circle with the triangle in it)

We were told the dishwasher expects to see the dish water temperature rise in a certain way. If the water does not heat in this way, the dishwasher becomes confused and thinks the heater element has failed. In deed, this happened just following and extended power failure and our hot water tank was cool. I am curious if this code will work for anybody else with the same problem and save a service call and 115 bucks. Overall, this seems to be a serious logic flaw in the design.